For now, I have several
handmade mechanical mods for sale.
For the detailed
information on the warranty, materials and the hardware, see questions 4, 5 and A2 of the
FAQ in my main thread.
To see more photos, go to my main thread as well.
Here are their specifications.
1. The Hamster.
- The handmade mechanical mod-stick made of AISI 304 stainless steel.
- Powered by a single 18350 battery (flat top).
- The height of the movable atomizer platform can be adjusted. It allows you to install any atomizer regardless of its height.
- The atomizer you’re going to use in this stick must have the positive pin that protrudes at least 1 mm past the threading.
Maximum atomizer diameter: 22 mm.
Atomizer compartment diameter: 23 mm.
If you want the upper part of your atomizer to remain at the same level as the upper side of the mod, its height must be within 14-29 mm (excluding drip-tip and connector height). The upper value is not the limit, the atomizer can be higher, but in that case its additional length (exceeding 29 mm) will be sticking out of the mod.
The stick is a perfect fit for the Nectar atomizer.
The firing button is mechanical, bottom side (soldered to the removable panel).
The construction of this stick includes a MOSFET transistor.
Dimensions: Depth 45-46 mm; Height 41-42 mm; Width 65-66 mm.
Weight (without battery & atomizer): 97 g.
Atomizer, drip-tip and battery are not included.
The mod is sculptured with the acrylic-polyurethane composition with natural material (wood); painted with acrylic colors; covered with transparent varnish and flock.
The finished coating is softer than polymer clay or epoxy, but firmer than silicone.
Keep in mind that flock is subject to mechanical abrasion, and white flock (the Hamster’s cheeks
) is also easily-marked. In other words, in case of intensive exploitation of the device flock may wear out and get dirty.
However, if it happens, you may clean it. You should soap up the dirty areas with soap solution and wash the dirt away with warm (room temperature) water. It’s necessary to blot the wet areas with a soft dry cloth right away!
If the flock wears out seriously, I can renew the coating of the mod for free, but only once. The shipping from you to me and back in this case is at your expense.
Price: 350$.
Methods of payment: PayPal only.
The worldwide shipping is free (included in the price).
The choice of the way of delivery is mine; the tracking number will be given.
Photos:
----------
2. The Toad.
- The handmade mechanical mod-stick made of AISI 304 stainless steel.
- Powered by a single 18350 battery (flat top).
- The height of the movable atomizer platform can be adjusted. It allows you to install any atomizer regardless of its height.
- The atomizer you’re going to use in this stick must have the positive pin that protrudes at least 1 mm past the threading.
Maximum atomizer diameter: 22 mm.
Atomizer compartment diameter: 23 mm.
If you want the upper part of your atomizer to remain at the same level as the upper side of the mod, its height must be within 10.5-26 mm (excluding drip-tip and connector height). The upper value is not the limit, the atomizer can be higher, but in that case its additional length (exceeding 26 mm) will be sticking out of the mod.
The stick is a perfect fit for almost any RDA.
The firing button is mechanical, upper (quite stiff!).
Dimensions: Depth 39-40 mm; Height 44-45 mm; Width 66-67 mm.
Weight (without battery & atomizer): 97 g.
Atomizer, drip-tip and battery are not included.
The mod is sculptured with the acrylic-polyurethane composition with natural material (wood); painted with acrylic colors; covered with transparent acrylic varnish.
The finished coating is softer than polymer clay or epoxy, but firmer than silicone.
Price:350$.
Photos:
Here’s a video demonstrating the look, the construction and the work of this device:
Some more photos of these two devices:
----------
3. The Stone Druid.
- The handmade mechanical mod-stick made of AISI 304 stainless steel.
- Powered by a single 18650 battery (flat top).
- The height of the movable atomizer platform can be adjusted. It allows you to install any atomizer regardless of its height.
- The atomizer you’re going to use in this stick must have the positive pin that protrudes at least 1 mm past the threading.
Maximum atomizer diameter: 22 mm.
Atomizer compartment diameter: 23 mm.
If you want the upper part of your atomizer to remain at the same level as the upper side of the mod, its height must be within 11.5-57 mm (excluding drip-tip and connector height). The upper value is not the limit, the atomizer can be higher, but in that case its additional length (exceeding 57 mm) will be sticking out of the mod.
The firing button is mechanical, upper.
Dimensions: Depth 30 mm; Height 70-71 mm; Width 47.5 mm.
Weight (without battery & atomizer): 96 g.
Atomizer, drip-tip and battery are not included.
The mod is sculptured with the acrylic-polyurethane composition with natural material (wood); painted with acrylic colors with the addition of the luminophore pigment (glows blue-green in the dark); covered with transparent acrylic varnish.
The luminescence is not permanent; the device glows in the dark after “recharging”: just keep it in any light (the brighter, the better; e.g. a desk lamp would be great) for some time.
Price: 300$.
Photos:
The following video demonstrates the look and the construction of this device:
----------
All the mods are 100% tested and ready-for-use. They’re entirely handmade and unique, there’s only one copy of each device. Every item can be used both as a vaping device or as a decorative figurine, an exclusive gift etc. These devices are ideal for stealth vaping: you can partly or completely hide your atomizer in them.
I accept payment via Paypal only.
The worldwide shipping is free (included in the price).
The choice of the way of delivery is mine; the tracking number will be given.
----------
Here’s another
video demonstrating all the three devices:
The position of the movable atomizer platform of all these three devices can be adjusted with the help of two screws in the battery compartment. Unfasten the screws to adjust the platform position and then tap them to fix it.
A video demonstrating this process:
