Search results

  1. Dakota Jim

    New from SD

    Yeppers, I'm in RC and more than happy to assist you anyway I can - once you get over 15 posts here you can start using pm and I can meet you anywhere in RC and answer questions for you and get you started with rebuilding or diy at your request
  2. Dakota Jim

    New from MN!

    Hey Manbear, welcome to the ECF and sorry about your loss. I have the Vamo v2 (2 actually) and the sigelei Zmax3 and actually prefer the sigelei as a carry around mod (I can telescope it down for 18350 if I am out and about). I am (unfortunately) naturally paranoid about people stealing it when...
  3. Dakota Jim

    New from SD

    Hey MWdrift - welcome to the ECF - sounds like you are in the RC area (TKO reference). I am coming up on my 1 year vaperasary and have some experience with most styles of vape gear (mods, mechs, RDAs, RBAs (including rebuilding Protank single coil heads) and DIY) so if you have any questions and...
  4. Dakota Jim

    I think I just overpaid

    I agree with Say10 - before jumping on the "you were ripped off" bandwagon all components of the purchase need to be listed ie: Vamo, charger, 2 batteries off most US based websites would be in the $70-90 range with no instructions and no easy fall back if there is an issue with it not working...
  5. Dakota Jim

    I wish...

    I wish Stanton Glantz would quit lying and misrepresenting data to scare people into banning vaping
  6. Dakota Jim

    RDA bad taste

    haggus, hotdogs or shrimp - just clean plain boiling water
  7. Dakota Jim

    Least Leak Prone Rebuildable Tank Set-up

    my experiences Aga-t - leaks like a sieve if not kept upright at all times kayfun lite + clone (similar to the Russian 91) leaks if vacuum is broken slightly protank 1 with an aerotank base - no leaks at all my 2 cents
  8. Dakota Jim

    Aerotank/protank rebuild problems

    I agree with Denvap0r, it seems like 12 wraps on a 16ga needle is going to be too big and when you tighten it down it is compressing something causing the short to the side wall of your atty head - try 30 or 32 ga kanthal with fewer wraps for better results in the smaller heads and use the 28ga...
  9. Dakota Jim

    vaping difference with ohms

    I am going to assume you are using a mechanical low ohms at 4 volts (I will use 4 volts as the base line for this) 4 volts @ .9 ohms = 17.77778 watts 4 volts @ 1.3 ohms = 12.30769 watts 4 volts @ 1.5 ohms = 10.66667 watts 4 volts @ 1.8 ohms = 8.88889 watts 4 volts @ 2 ohms = 8 watts 4 volts @...
  10. Dakota Jim

    New Member, some basic questions

    smokeless image also has an 808 threaded Nano clearomizer also that fits nicely on the G6
  11. Dakota Jim

    Forum use ?

    the reason you can not edit posts after 24 hours is to keep continuity in the original post People read old posts all of the time (I get likes on one of my stupid jokes from over 2 months ago still) I try to only edit to correct spelling so peeple dunt relize I be unedgycated or to add extra...
  12. Dakota Jim

    Looking for comments on Vuze e-cigs vs Volt, Halo, etc.

    Vuze is owned by big tobacco and currently is only available in CO I have some Halo G6's I started with and liked and my stepmother has Volt which she likes only downside is the 808 threading but once they upgrade to an ego style battery (but not the Halo Triton which uses the 808 and VGO...
  13. Dakota Jim

    MVP2 Charging question

    My MVP1 stays green until I unplug the cord - It takes about 3 hours to charge fully from a wall charger Remember that Li-Ion batteries have no memory effect so you can unplug from the charger whenever you want (but don't leave plugged in for weeks on end)
  14. Dakota Jim

    Questions about RDA's, RTA's and Pro Tanks....(May be a little long)

    Hopefully you did thoroughly clean your new RDA's before using. It seems none of the manufacturers can be bothered to clean the machining oil completely off of their devices before shipping out. The airflow on these devices is different from what you are used to also which I have discovered...
  15. Dakota Jim

    Old e juice tasting worse than new

    I have some 10 month old juice I just tried and it showed no loss of flavor at all for me don't know what to tell you
  16. Dakota Jim

    Vaping + Nicorette

    the actual absorption of nic from vaping (and probably the Nicorette also) is about 25 to 33% less than actual smoking so I would not think there are any worrys also you are spreading it out of the entire day so it does have a chance to leave your system Trust me you will know if you over do...
  17. Dakota Jim

    Obbsessed

    Here is what I got into with in the first 3 months of my starting vaping (* items are from month 4 to now) 2 vamo's 1 MVP1 *1 Zmax 3 *1 Nzonic mech 2 Ego Twists 650mah 2 Ego 350mah (1 is always in my pocket - just in case - remember high school and that ring imprint on your wallet) 1 Ego...
  18. Dakota Jim

    Introduction and a few questions about MOD's / MVP 2?

    the delay may be from the gauge wire you are using. 28 gauge kanthal is beefy wire and does take a bit to heat up on regulated devices (most regulated devices have a low amp limit to protect the batteries and 1.3 ohm is the low end of most allowed resistances - low ohm builds are mainly for...
  19. Dakota Jim

    Cartomizer for cartotanks on Provari Mini

    The burnt taste in cartomizers is mainly from a dry hit (it may not recover from this - sorry) did you make sure you primed the carto with your eliquid before inserting it in your carto tank? you always want to make sure the carto is completely filled with eliquid before inserting it in the tank...
  20. Dakota Jim

    Silica

    I use from .6 to 3mm silica - just depends on how many strands you thread through the coil 2mm is the easiest to work with for the way I build coils and I just use a double strand through the coil if braided silica is an option where you order get it as it is easier to work with
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu