Search results

  1. grainey1968

    Victory over aga-t!!!

    I have made a few hybrid wicks and my best performance was from a cotton surrounded by a thin layer of SS mesh (just to minimize the chance of dry burning). Everything had to be rolled quite loose. Worked pretty good on the higher gauge wire (30 / 32) and shot for around 2 ohms. And yes - it was...
  2. grainey1968

    Victory over aga-t!!!

    3 inch of ss and 3mm of silica running thru it. That is one big wick. What size is the wick hole??
  3. grainey1968

    Crazy clouds with Bakero wire

    I purchased this from KP. I use it in my IGO L with XC 116 (1/32) ceramic wick. Serious clouds and flavor is sooo clean. V good stuff!
  4. grainey1968

    Looking for recommendations

    MustangSallie - just one more suggestion. You could try the Cobra clone and if you like it, you could get the real version (glass tank, titanium, top quality). I have both myself and I love my Cobra (the real one). Loads of options with wick/ coil on the real Cobra. I only suggested the RSST for...
  5. grainey1968

    Looking for recommendations

    Maybe MustangSallie would be extremely grateful if by chance she was to drop her $150 device. At least the tank would not break!!! LOL.
  6. grainey1968

    Rsst question

    My solid wicks in a RSST is closer to 4inches wide before I start to roll. Takes a bit of fingers and thumbs pressure!
  7. grainey1968

    Looking for recommendations

    Seriously!
  8. grainey1968

    Ceramic Wick Finally Performing Well.

    Couldn't agree more. My best setup is still with 30g kanthal hot wrapped. Took me a lot of practice and 1 broken FC wick to get it right. Take your time when wrapping your coil (slow, steady and even pressure) and the result is definitely worth it. The smoothness of the vape is fantastic...
  9. grainey1968

    Looking for recommendations

    AC9 Tank – Vapinaze
  10. grainey1968

    No flavor from IGO-L

    Do you have the materials for a <1 ohm setup. I use my IGO L at 0.9 Ohms and crank it up to 3.7V at this thing hit so well! 30 Gauge or even 28g would be good. Ribbon kanthal even better. I have used my 0.5mm x 0.1mm ribbon on this also and the TH, V & F was great. Maybe I have been getting...
  11. grainey1968

    Rsst question

    Should have added - I have a RSST and the flavor is great. Maybe not as good as some other RBA's, but it is more than adequate!
  12. grainey1968

    Rsst question

    Hi STLJohnny. How long have you had the wick/ coil installed? By this, I mean how many tanks of juice have you gone thru? Typically you would need at least 2/3 tanks before the performance is best (if you have set it up correctly). Give it some time to bed in i.e. the wick and coil need to...
  13. grainey1968

    Looking for recommendations

    Only suggested the RSST to be a tester for a more expensive RBA and if MustangSallie likes it, she could move onto the AC9 (with the bullet proof glass tank).
  14. grainey1968

    AGA, wicking issue? Diagonal cut mesh???

    Only thing else that I can think of - are you washing your mesh before you start. I normally put some dish washing liquid on my mesh and then wash it off with hot water (some guys even boil it). I do it more of a habit now to eliminate any oil or leftovers from the manufacturer/ supplier. I...
  15. grainey1968

    Disappointing experience with my AGA-Ts so far.

    Corgi - why not start from the other end? I mean, figure out exactly what type of TH, V & F you are looking for and then decide what materials (gauge of wire, wick type etc) could give you that in your AGA T2. Sounds like you are trying every combination and the seeing if that works. Just a...
  16. grainey1968

    Looking for recommendations

    You could try an RSST. If you get this figured out and working, this could lead you to the AC9 (the RSST is the clone of the AC9). You might even keep the RSST as this is quite a good RBA for less $'s and get the performance you require. The RSST is a good one to start with and IMO and can be a...
  17. grainey1968

    AGA, wicking issue? Diagonal cut mesh???

    Cutting the mesh in a diagonal will not help your wicking issue (I only do this for U wicks). I agree with Rule62 on the lengthwise grain when using a single vertical wick. Are you over oxidizing your wick (not able to breathe) and clogging up the grain? Have you tried pulsing an non oxidized...
  18. grainey1968

    Taifun GT...a mystery wrapped in a good amount of my money

    Thanks looks a nice piece of kit. Especially with the Provari (looks as though it was made for it)! What was the Euro price? Edit: Sorry didn't see the link above!:facepalm:
  19. grainey1968

    Help with igo-l setup

    Totally agree Jerms - 31 gauge is the best "in-between" wire that works with most possible builds! Stuff rocks!
  20. grainey1968

    So I'm thinking a reomizer 2.0... and a RSST

    Everyone who starts into RBA's will have questions. None of them are stupid. But, it you don't ask, you will have to figure it out yourself (like the more experienced at RBA's). I only wish I had of known about this site a few years ago and ask some vets and saved myself a lot of headache!! We...
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu