Search results

  1. Cisco

    e Liquid and adhesives

    There is no doubt about that. Cisco...
  2. Cisco

    cr2 replacement

    There is a smaller cell 14250, it is very close size to a cr2(15270), problem is neither of them come in protected and having them custom made is turning out to be a chore. Seeing as there being used above there max output range, its causing the protection circuit to kick in rendering the...
  3. Cisco

    Oh boy!!! DIY parts from Chinese suppliers....

    Maybe you never looked hard enough...:D AltSmoke Battery Adapters - Adapters - PV Parts Cisco...
  4. Cisco

    Oh boy!!! DIY parts from Chinese suppliers....

    Well, It was only a matter of time and some great news for modders..... DIY Materials - Wholesale & Retail Best E-smoking Supplier Cisco...
  5. Cisco

    **BOOM!** Battery Failure

    I would agree with that statement q. Its the only device where you can "See" the vent holes. FYI the SB has venting capability built in, you just don't see it, just because you don't see it doesn't mean its not there...:D...
  6. Cisco

    Mini N.O Momentary Switch ?

    It will work, but not for long without the use of a mosfet. Manual e-cig batteries use the same style tact, but there driven by a mosfet. Almost all tactile switches are rated at 50ma max and are designed for circuit activation via other components.The current to the atomizer does not travel...
  7. Cisco

    **BOOM!** Battery Failure

    Agreed Parma, That could have been much worse, glad to see you came out of this with relatively minor damage. People do need to understand the potential hazards when using 2 cells in series and Lithium-Ion batteries in general, protected and unprotected, bad cells are not limited to unprotected...
  8. Cisco

    **BOOM!** Battery Failure

    When using 2 3v cr2 in series to achieve 6v vape you are using these batteries above there max rated output, If you vape excessively there is a small possibility that they could get hot enough to vent, but highly unlikely. I don't know the facts or variables in Parma's incident but sounds more...
  9. Cisco

    Over-charge Protection w/ Trustfire All-in-One?

    This charger is for 3.6/7v batteries only, not 3.0v batteries DO NOT put any 3.0v battery in a 3.6/7volt charger. You need a charger made for 3v lithium batteries. All lithium battery chargers have over charge protection, it is the reason you should use chargers for the batteries there...
  10. Cisco

    So what batteries are out there?

    No such animal in Li-Ion, its either 3v or 3.7v, with a few 3.6 and a few 3.2 in the mix. The chemical makeup is the limitation. If you see any li-ion in any other voltage, its either multiple cells or some sort of boost/resistance regulation. The difference between 3.6/3.7 and 3.0/3.2 is the...
  11. Cisco

    Laser Pointer mod Guide

    Well said Nerf.....:) I got the protected batteries to fit. They are more then 1mm longer so it is an issue, trying to fit them in was putting to much pressure on the spring and causing the switch to get jammed up. I needed to bore out some of the material on the bottom of the end cap. I got...
  12. Cisco

    "I saw, I liked, I machined, I vaped"

    Bubo was just showing how long it took for someone to ask me to make another, after I clearly said I was not making any of these. Cisco..
  13. Cisco

    Sneak Peak of the Mini-T!!!

    Well said breakfast Oh and Lisa, here is a tissue, you have a little something on your nose.... Cisco..
  14. Cisco

    "I saw, I liked, I machined, I vaped"

    Thanks Bubo, When you push the button the post slides up through the bushing and makes contact with the negative on the battery there for completing the circuit. Cisco...
  15. Cisco

    "I saw, I liked, I machined, I vaped"

    I saw this mod and thought it was pretty stealth looking, I was curious to see if I could make one, so I did. 510 recessed connector, rear switch, 10440 protected battery, no solder and no wires. The protected cells are 2mm longer so I put a spring in to accommodate non-protected Mind you, I...
  16. Cisco

    Sneak Peak of the Mini-T!!!

    David, your machining skills are unmatched, and your mods are way under priced. Real nice job on the Mini-T. I hope the price will reflect the craftsmanship Cisco....
  17. Cisco

    True PENstyle 501 e-cig

    Nice job Shreck, now you have the "Write" to vape.....muhahaha...:D Cisco...
  18. Cisco

    Laser Pointer mod Guide

    It was never about making money, although I could have made a pretty penny...:D This guide was put here to give people the opportunity to mod themselves instead of paying silly amounts of money for what is basically a tube and a switch. This was way to easy of a mod to keep to myself. I can...
  19. Cisco

    Greencig Cartomizer Autopsy

    So I got a few used Greencig Cartomizers (Thanks RsL) to take apart and see whats going on inside these things. I pulled the connector out and was expecting the entire insides to come sliding out ,but they didn't. What came out was the connector, and connected to that by 2 feed wires was a...
  20. Cisco

    Some cool MODS I made

    Nice job rannie, don't take this the wrong way but I really like the "Woody"...:D, the other one nice also, but it doesn't do anything for me...:lol: Awesome job on both mod's brutha... Cisco...
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu