Search results

  1. Cisco

    Solitaire mini mag with push-activated atty

    Nice job Dan, now I don't have to do a guide....:D That is how my original one worked, using the end cap spring for tension, but the protected batteries are longer (2mm+/-) and in that mini mag they completely compress the spring with 0 play left.....:( Cisco...
  2. Cisco

    Cartomizer disassembly

    No it does not. The coil is in between the hollow tube and the mouth piece. When you draw it pulls air through the center connector up into the hollow tube.The air then leaves the hollow tube and is pulled up across the coil. As the air passes the coil it pulls the vapor being created into the...
  3. Cisco

    Automatic box mod

    You are correct Cash http://www.e-cigarette-forum.com/forum/modders-forum/38210-look-ma-no-hands-automatic-switch-sd.html Cisco...
  4. Cisco

    strange

    Check the ohm reading on your rear end click switch, they are notorious for having a 1/2 ohm + of resistance. also the shell is the ground check the ground from the rear click to the atty connector should be no resistance. Cisco...
  5. Cisco

    Re built my first atty.

    Hey Carlos, I think what your using is not ceramic its actually Porcelain, much more dense then ceramic and has very a low absorption quality. If its breaks like glass its porcelain, definitely take precautions in cutting this stuff, broken pieces are as sharp as razor blades. Ceramic is much...
  6. Cisco

    Solitaire mini mag with push-activated atty

    In the next few weeks I will see if I can do this mod with "off the shelf" parts. If I can, I will put up a guide, then everybody can make one...:) Cisco...
  7. Cisco

    First Mod - Manual PS

    Doesn't matter what it looks like, if it works and it was cheap, you win...:D You could buy a PS PT for $70.00 if you want pretty...:) Cisco...
  8. Cisco

    Solitaire mini mag with push-activated atty

    I had them made.... http://www.e-cigarette-forum.com/forum/battery-mods/40233-promised-10440-protected-cells.html Cisco....
  9. Cisco

    10440 li ion protection board...would you pay $6??

    Don't know why you would want to make these by hand, Hopefully your not soldering the Protection boards to the batteries with a soldering iron, that would be kind of dangerous. http://www.e-cigarette-forum.com/forum/battery-mods/40233-promised-10440-protected-cells.html Cisco...
  10. Cisco

    Cartomizer disassembly

    You could thread the cartomizer onto a battery and rock it back and forth to break the connector loose, I am not sure if you will pull the battery connector out first. I would try it with a dead battery if you have one. Cisco...
  11. Cisco

    Laser Pointer mod Guide

    I don't know, Put a meter on it....:D Cisco...
  12. Cisco

    The Carbon Mod

    Awesome job Mix, The carbon fiber adds a nice touch... Cisco...
  13. Cisco

    Solitaire mini mag with push-activated atty

    I used all the parts from the flashlight and nothing from the flashlight is modified other then sanding the black finish off of the inside of the head for ground contact. The atty connector is pressed into a brass ring I made that slides inside the cap. The center post and sleeve I also made but...
  14. Cisco

    Cartomizer disassembly

    Not much inside, The initial view after pulling the connector out of the shell was a coarse fiber fill that somewhat expanded as I slide it out. After unwinding it there was a second layer of a finer fiber wrapped around the coil. After removing the second layer the coil was exposed. The coil is...
  15. Cisco

    Solitaire mini mag with push-activated atty

    This solitaire mag light has been sitting on my desk for weeks, It was SuperSteph who modded this mag originally and made a pretty cool rear end switch. I couldn't figure out how to get a manual switch in such a little shell because I am not a fan of rear end switches. So using Muldrick's...
  16. Cisco

    Challenge

    No wonder you wont make one yourself, I currently have 10 fingers, and would like to keep it that way....:D Cisco...
  17. Cisco

    Looking for Nerf...or how might one...

    http://focus.ti.com/lit/ds/symlink/ptn04050c.pdf Page 15 I would think a box style mod, 7/8" x 1/2" x 1/2" thick Cisco...
  18. Cisco

    Looking for Nerf...or how might one...

    The Vin range for a PTNO4050C is (2.95 V to 5.5 V), 2 3.7v li-ion cells in series will have a full charge voltage of 8.4, way beyond the max limit, I would consider 2 cells in parallel. Cisco...
  19. Cisco

    battery tubes...where to get??

    McMaster-Carr The closest they have is .50 OD x .444 ID, it is about 11.5mmID,12.5mmOD in a .028 wall thickness. runs roughly $7.00 per ft. Cisco...
  20. Cisco

    Classic "Hot Rod" 510 Magnum Mod

    Yes, Acetal(Delrin) is very easy to machine, its a self lubricating material and has excellent insulating properties, its very dense and can be machined to very tight tolerances. Acrylic is a PITA to machine, enough said...:) Cisco...
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu