Search results

  1. steved5600

    Dual coil build - Tobh clone

    A pic would help.
  2. steved5600

    Steeped E liquids

    Cap off is bad advice. Can cause the flavor and nicotine to oxidize. Ultrasonic cleaners will do it. Room temp or warm water temp and shaking. They make a thing called a milk frother a small battery operated small tip mixer but be careful I believe they only have one speed. FAST. I made a...
  3. steved5600

    brass plated copper?

    Copper plating will do much for conductivity as its only a few molecules thick. It's just for show. Brass is better than Stainless steel and aluminum though. A mod with a copper inner sleeve would be but I know of none like that yet.
  4. steved5600

    rebuilding coils

    You don't say what battery you're using. Some batteries like the egos work best with 2ohms. At least that is what they say. If you rebuild a head in a tank system like the Vivi or Protank you need to use NR-R-NR wire. Its resistance wire with low/no resistance wire leads. Otherwise you...
  5. steved5600

    aerotank mega which coils should I use

    You can use the PT3 coils in that. The ones that come with it I believe are of the new trend of enclosed wicks. Not a big fan of them because they are a bear to rebuild. I have not tried that new head but did try the one made by aspire for the PT1-2's etc. Did not like it.
  6. steved5600

    How to clean c2 joyetech atomizer?

    IF you are talking about the replaceable head I used the predecessor to the c2. I never had much luck with them. You can try soaking them in alcohol and doing a dry burn but my bet it won't work. 15 days on a head is a good live for a head.
  7. steved5600

    So excited now just have to wait on Fasttech lol

    If your not a vape mail nut like me Fasttech can be good. Some of their stuff is not so good but you can look at the reviews. Count on 3-4 week waits and be happily surprised when it gets there earlier.
  8. steved5600

    New to RDA.

    If you can do cotton for sure it can be better. Make sure you use organic unbleached cotton. You can find it at places like Whole foods and online. Remember with cotton less is more don't pack it.
  9. steved5600

    Dual coil help

    You can double it. If you have a 1.8 ohm head in the Nautilus each coil is 3.6 ohms. So you could to 5 volts and you would get about 7 watts per coil. This should be doable if the wick can keep up.
  10. steved5600

    Trident post problem

    May want to consider going to a different RDA. I never liked those damn posts. Take a look at the IGO-w3, Stillare Storm clone, Tobh Atty V2 for sure, maybe a hades. Stay away from ones like Brass Monkey. The center T post on that is bad news. Don't like the Enigma clone either.
  11. steved5600

    Mvp w/kayfun problem

    May be a problem with the center pin. They sell insulators for that on Kidney Puncher and Fat Daddies. Or you can google Kayfun insulators.
  12. steved5600

    New mod vaper looking for advice!

    Get the Protank III or It's a dual coil and is better than the II. The coils are rebuildable to. You will like that charger just check to see if it comes with all the cables some don't. I have a Nightcore 4 bay. Vamo v5, and 3 PT IIIs. Love bottom feed coils..
  13. steved5600

    Don't understand how.

    Here is what the wire looks like. $2.47 Pre-made Welded Wires - NR-R-NR (100-Pack) 100-pack - 0.15mm / 2.6ohm at FastTech - Worldwide Free Shipping
  14. steved5600

    Don't understand how.

    The Aspire is a dual coil. Dual coil in parallel. So if you have two 3.6 ohm coils you get a total resistance of 1.8 ohm. Going to give you a formula. 1/resistance in ohm + 1/ohm .....= 1/total resistance. Or in the case of dual coils just devide by two when deciding what resistance should...
  15. steved5600

    Vamo Question...

    Don't know the Vodo tank but do know the Aero tank. I've had two Vamo's. The Vamo will not go below 1.5 ohms. I am a big rebuilder. So I know a few rebuildables. First get an Ohm meter. Get either a simple meter available at radio shack or even WallyMart. Or get one of these: The...
  16. steved5600

    MVP 2 Pin pulled PLEASE HELP

    Need a picture to tell much. Is the wire still attached to the pin and inside the mvp? You may be able to unscrew the case and resolder it. But with out a pic I can't tell .
  17. steved5600

    Chi You Clone from FastTech (Need Tips, Adjustments and Upgrade Ideas)

    May want to use the Chi you ultimate upgrade kit here. Has an better parts and a magnet spring upgrade. SHOP - FatDaddyVapes.com - Home of the best vape tweaks and replacement hardware. THe chi you parts are at the very bottom. I got parts to fix my #19 an a couple of Kayfuns with problems...
  18. steved5600

    Sweetner?

    I believe TFA sweetener is Liquid sucralose. That is an excellent vaping sweetener. You can also use Ezsweetz can get 5ml for $1.00 shipping charge. Look for the free sample on google. Just don't use organic sweeteners or the other artificial sweeteners.
  19. steved5600

    Water Vs Alcohol

    Why are you adding either. Alcohol should be avoided it's not meant to be inhaled. Are you looking for TH. In any case stay away from alcohol. Alcohol causes cell damage. If you us a lot of alcohol on your skin what happens?
  20. steved5600

    DIY Liquid: Any order of mixing?

    Does not matter in the mixing but you need to keep doing it in the same sequence each time. You should not need to add water. But i you do use distilled water. Hope you did all your homework on mixing and are using some kind of recipe software. As long as you do it the same way each time...
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu