Search results

^^^what's been said^^^ vape it!

I screwed up on my last refill. Wound up putting in 8mg juice instead of the 3mg I had previously been using. To remedy the situation I turned down the power and closed the AFC down to just 1 hole. Running at 3 volts now. Meanwhile built a dual fused clapton for the 2nd deck with larger...

Going to make some fused Clapton wire today and hopefully try out the other deck.

If using TC am I best off building resistance higher?

I did. 11 X 120ml and 3 X 60ml. What I'm liking about Boreas is that I can refill it, by pouring directly from a 120ml bottle. Makes for a quick refill. Still using same coil and wick from Thursday. 316L SS 26 ga dual 3mm spaced .23ohm wicked "tight" with rayon. Power mode 60 to 70 watts...

Had to mix some juice!

No misfires here. First week with mine. (silver 2nd batch?)

With the wide spaced text cell charged to 4.2 was able to fire from 60- 70 watts. (.24 ohm 26 ga dual parallel 3mm id) Mostly kept power in the 60-65 range as I didn't want to push limits. Switched to a .59 ohm tank with remaining battery of 3.8 and ran down to 3.4 until "weak battery"...

I've been on the fence about returning them due to all the bad reports I've been seeing. I guess I'll try them and report back. Looking forward to the test results for best cell.

Received two 26650 MNKE's from RTD Vapor. They are the one pictured with the sticker and the text is not spaced close.

Been following this thread. Just got my serpent going this week. 24ga A1 Kanthal 6 wraps spaced 3mm wicked with rayon. Got some leakage with AFC closed, while top filling full, after putting top cap back on. Before my last fill, removed base and stretched a 13mm x 11mm X 1mm o-ring onto the...

According to Preston Kight of VF 67 mm is the max length recommended for use in the Stout. My silver should arrive on the 9th.

After opening up the mod, removing all the hot glue and checking all the solder points, I reassembled the 510 connector into the C-frame, installed a battery and was able to get the SX300 chip to work again. Got everything back together now with minimal amount of hot glue holding the chipset in...

After 3 months of daily use it stopped working. Screen does not come on and atty doesn't fire when button is pushed; at least it didn't catch on fire. This had become my go to mod. Anyone have any advice on opening the mod up to check wiring? I may be interested in replacing the chip as...

Received my Hotcig SS on Tuesday. Sleeve was a loose fit and needed to be squeezed. Bolt heads stick out beyond flush; haven't removed them or tried to tighten them up yet. Seems to me that the counter sinks were to shallow when manufactured. VTC4 battery fit easily with brass screw backed...

I'm in on the pre-order for the stainless. Emailed Doris for conformation number. Order was placed through FC website. This will be a step up for me from my 3rd round V1 Cloupor Chana that's still going strong with all it's quirks. The wait begins...

Round 3 version 1; still going strong. Received early June from 101vape. Charged daily with USB. Unit has not yet powered up on its own, but exhibits all of the other quirks reported of earliest version. Noticed indents in my button finger/thumb from day one. No complaints with purchase.

Your atomizer is not making contact at the 510. Your Tesla will display 9.9 ohms when there is no atty attached as well.

I'll be 51 this month. Was smoking 2+ pad until 10 months ago I was ready. Mel Gibson once said in an interview I saw on TV years ago that still sticks in my mind, "you can't quit if you don't smoke". I couldn't imagine not smoking. I started with a simple ego and tank starter kit and...

With my KFL+ I've placed a small strip of teflon tape on the grub screw thread to help prevent it from unscrewing on its own and getting stuck on my SR. Preferred RTA for my SR is the R91 with grub screw on the side. So far so good.