Thanks. I ended up buying the Crown 3 as well. Very happy with this tank. I have nothing bad to say about it at all. I haven't had one leak yet, use a little more juice than I used to but as mentioned....comes along with the sub category so I've brought that on myself. Side note that I've...
Hey, folks! Recently purchased the Wismec RX Gen 3 kit and the Gnome tank just doesn’t cut it for me...gets very hot in a short period of time even while vaping under recommended wattage. I’d like to get a new tank to go with the mod (which is great so far) and am looking for a solid...
Just purchased the Gen 3 kit a few days ago and really like the mod itself. However, I’m no fan of the Gnome tank. When vaping at anything higher than 45watts (which I do otherwise why buy the Wismec except for long battery life) the top gets ridiculously hot! This might be ok with the extra...
@suprtrkr Thanks for the response. I've now tried just about everything and getting ready to head to local vape shop to see if defective. Probably too late since I've had the device a while.
Thanks for the response. Not sure what "bump" for an answer means but I'm thinking the initial 200degrees setting is too low for SS so I'm going to try some different settings (temp, watt output, etc...) and see if that makes a difference. Will post a reply if I find an answer for anyone that...
Hey folks,
Have a problem that I have not been able to figure out or gotten a good answer about. My current setup is X Cube Mini with Subtank Mini with the new SC SS coil. When I try and vape in TC mode the coil burns hot after 1 sec and I get the "too hot" warning and system shuts down. The...
Hey, just thanking you for your service! USMA grad and Signal Officer of 11.5 years now living in WV (hometown of my wife.) Born in Germany, son born in Germany, stationed in Germany among other places. Injured in '09 and medically retired in '11. Here I am Vaping! Newest in the pocket is...
Hi. Just got the X Cube Mini with Firmware 1.02 installed but SMOK seems to have a later version available. Every time I try to "check version" it says it failed. Not sure why this keeps on happening. It states you are supposed to do this before you plug in the MOD but I just can't figure it...
Just got the X Cube Mini and had been using a Sigelei 75W. Initial thoughts are that the Sig is better quality build, more solid and feel as a bit better in my hand. With that, if you have the "extras" on the Cube off (lights,etc...) the battery life is a lot better and the many functions are a...
Just got one...came with sleeve. Make sure device is off and locked when you put it on cuz it's a pain to fit properly w/o hitting the firing bar a million times. Wish the sleeve was a little thicker too but hey, at least it came with one! "E" for effort
Hey folks!
So, I purchased a new Kanger Subtank Mini about a week ago and the O-rings seem to be bigger and tighter than the first version of the tank which was supposed to cure a problem a lot of folks were having with the tank leaking from the bottom of the pyrex glass. However, my tank...
I love everyone's posts. In all honesty I would gladly donate any $ spent on Christmas gifts to the welfare of my Veteran Brothers and Sisters...there's lots of work to be done for them and they shouldn't have to drop a dime! (I will not, however, give anything to crappy WWP...side note!)
On...
I want a SMOK Xpro M80, Subtank Plus and my gums to grow back. Apparently, according to my wife, I only need one mod?!? Not sure which world she's living in...that's like a baby only needing one diaper change per day!
I love my Kanger Nano tank...perfect pocket size w/ good airflow and holds decent amount of juice. However, I'm using it on an eLeaf TC40W w/ .5 Kanger coils and found my nice spot at about 21watts. The drip tip seems to get entirely too hot. Is this because the tip is just so thin, draws too...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.