Search results

  1. JoeMoto

    The Ms. T order status thread

    Order# 12376 placed on 7-11-11. Still awaiting fulfillment.
  2. JoeMoto

    Needing Modders Expert Advice on Item I Found

    Not enough amperage. You need 1.5a minimum, depending on the atty you use. A good range is 1.5a to 3a.
  3. JoeMoto

    Making an Atomizer Coil 101 (Actual Working Methods Only)

    Thanks Vaporer, I'll try that. I have a problem with trying to slide the connector back into the tube. It will push the coil up out of the cup.
  4. JoeMoto

    Making an Atomizer Coil 101 (Actual Working Methods Only)

    What adhesive are you guys using to glue your wires to the bottom of the cup so they don't push up when you reassemble the connector into the tube? I've tried hi temp silicone and some tacky glue but neither seem to adhere to the epoxy coated magnet wire.
  5. JoeMoto

    Ceramic Atty Cups

    That sounds great Dan, I'd love to get some pics of your design. Have you drawn them up in Autocad or anything yet? I'll send you a PM.
  6. JoeMoto

    LED problem...

    If you have a wire running from the master switch to the momentary switch put the resistor leg of the led on either end of that wire. Good pics will help.
  7. JoeMoto

    Ceramic Atty Cups

    Is there an interest in new/replacement ceramic cups for atty building? I'm working with someone on getting some supplied here in the states. I need to draw up the cups dimensions for the price quote. I have a 510 for reference. What other sizes are desirable? I have an 810 and 901 coming this...
  8. JoeMoto

    Juicebox Atty?

    What ohms is that atty? Did you have plenty of juice in the wick when you were vaping it? I haven't seen a wick burn up like that.
  9. JoeMoto

    Removing the barrel from a 510 atty?

    A heat gun will loosen the glue where the tube attaches to the connector threads. Or boil in water for 15-20 minutes. Thread the atty onto a broken battery or an old battery connector that is held in pliers. Wiggle them against each other and they should come apart. The wires are soldered to the...
  10. JoeMoto

    Juicebox Atty?

    Thanks guys. Clyde, I'm way down yonder in Durant, about 30 miles north of Sherman, Tx on Hwy 75. It might be a little far to drive just to show me. :D But some high res pics would be awesome! Especially down into the atty. And maybe some dimensions?
  11. JoeMoto

    Juicebox Atty?

    Clyde, So it is a machined brass cup, with a single hole at the bottom corner of the cup? Is the hole in the side, bottom or the corner itself?
  12. JoeMoto

    Juicebox Atty?

    I was also curious and started reading his post history. If I'm not mistaken he was using 32ga wire when he started rebuilding pipe attys. That may be one reason they last longer. 32ga is quite a bit larger than the 38 or 40ga that stock ecig attys use. In fact, 32ga is twice the diameter of...
  13. JoeMoto

    please help with copper pipe mod

    The IRL is the one I use. I used the same small tactile switch you have in my latest mod with a 5v booster. Without a booster the wiring is Batt- > Source Batt+ > switch > Gate Batt+ > Atty+ Drain > Atty- From what I've read the n-channel mosfets are more desirable because the p-channels...
  14. JoeMoto

    Pay it forward - USA - please read 1st post for rules and guidelines

    It's the Mad Vapor subbrand that Walrus mixes for them.
  15. JoeMoto

    Pay it forward - USA - please read 1st post for rules and guidelines

    I'll take that and offer 10ml Dekang RY2 11mg ~15ml Liquid Express MV Thin Mint 12mg ~15ml Liquid Express MV Apple Pie 12mg
  16. JoeMoto

    The Mini Juice Machine Mk 3

    If you are looking for silicone tubing I've been using some that I got for direct dripping. It can be fed into the bottle and the cartridge and there are no leaks and no sealant. I drilled out the drip tip on a 3ml bottle with a 3mm bit and slid the tubing in. It will also slip over brass tubing...
  17. JoeMoto

    Anyone care to sell atty supplies?

    You can get nichrome here. 36ga. is 10' for $2 or 30' for $4 shipped. Go to your local hardware store and ask for wood stove door seal. It's braided silica or fiberglass. I got a 3' long 1/2" diameter piece for $3.
  18. JoeMoto

    Mad Dog's Magnum Mod Help

    You need to add another wire from the board straight to the switch, parallel to the led/resistor.
  19. JoeMoto

    Question with atty OHM test

    I have that same meter, although it's 2 years old, and it "zeros" on that setting at .9 ohms. Just subtract your "zero" value from the reading and that's the actual value. It was only $3, so you get what you pay for. So yeah, what Rocketman said.
  20. JoeMoto

    Any Mocha Recipes?

    I've been vaping Starpuffs from cignot and am loving it. Does anyone have a mocha recipe handy? I'm using PA flavors, but am willing to get the those required.
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu