Search results

Any feedback from these suggestions? I am interested if anyone has given these a try. And thank you Baditude

What he is tasting is most likely burned cotton or other wicking material. It is impossible to burn juice. Ask him to make sure he follows the recommended wattage on the side of the coils.

Reasons why electronic cigarette(ecig) tanks leak. The majority of leaks are due to excess juice within the airflow chamber and/or coil. Other leaks can be caused by missing or damaged o-rings, insufficient wick material(commonly cotton), broken glass, loose or overly tight connections. I intend...

I both lung inhaled and mouth to lung inhaled when I smoked analogs(26 years). With electronic cigarettes(ecigs) I always go straight to the lungs. Their are two ways I control the amount of vapor and air inhaled. The first is to limit the speed which I inhale. Limiting the speed also limits the...

This video instructs how to almost completely fill the Kangertech Sub tank mini ecig tank. All it takes is to block off the center hole which normally prevents filling the tank any further then the height of the center post. I used a Dremel mandrel approximately .170 inches(4.33mm) in diameter.

I finally received the Aspire Nautilus mini but quickly realized you need a very high wattage power supply to keep it going. It's not for me with my little ego batteries. Is the Kanger Aerotank a high wattage device too?

Disregard my dislike of the K1's, I must have had a bad bvc coil. I replaced the first coil and it is still going 5-6 days later. I must have cooked the first bvc coil. I have yet to take apart a spare to compare the material used for filler but I am certain the original supplied with the k1 was...

Well the Aspire K1's were delivered and it was a perfect replacement for the iclear16 tanks......until disaster. From about 5 hours into it I noticed I had to continue increasing the voltage for the same vape. The first head which came with the BVC was either a dud or a normal failure for these...

No problem, Happy Vaping!!

I like the looks of those and it looks better with the pen top. I have had other tanks laying sideways in my coat pocket or car seat and they leak out so I could use a screw on top. I'll give it a try on my next order and thanks for the link as I buy most of my supplies from Madvapes.

Hey Mike, I just got back to this thread after getting my Aspire K1's. These are the "glass" I was referring to. So far they seem to have really good flavor and I cannot taste anything from the tank itself, no burning, no oils, nothing bad at all. It is almost the exact size as the iclear16...

I understand you were trying to help but most people don't respond well to an insult along with the advice. I am one of them. Safety had been mentioned prior to your post. Holier then thou may not have been a good description just my first thought.

Thank you t2ak, I bought both the nautilus and the Aspire K1's to see which I like the best. Have you tried the 1.2 ohm heads with ego type batteries? Sometimes they cut off if the resistance is to low. Do you think they would work on VV ego type batteries?

The purpose of this post was to find a replacement. I do find it worth the hassle to stretch these a couple weeks while I wait for my Chinese glass replacements. The epoxy was placed over the joint prior to breaking so I feel safe vaping these in the short term. I am more concerned about the...

No it was epoxied before a crack appeared. I'll watch for problems and am sure I'll be fine. Thank you

Not so much on these. I have some common sense. These were epoxied prior to a crack forming. This was a preventative measure which has little to no chance of getting into my liquid. If your the kind of pushy holier then thou person I think you might be I'll be patiently awaiting your response.

cannot delete

The pictures above do not show bulging, that is epoxy as I described in the original post. The "swelling" I referred to was on the base of the black tip we use to draw the juice. Where it touches the white cap it swells and becomes soft and pliable. From what I have read above this does happen...

What is shown in the picture isn't bulging. It's epoxy. The bulging was a softening and warping of the black tip as I described in the original post. Sorry for any misunderstanding.

I like the looks of the Aspire Nautilus Mini. I found one on Fasttech but I know they sometimes are not original. I think I'll give it a try. thank you