306 atty tank using a DCC tank

[kwalka]

Just found a completely unintended benefit/consequence of the 510 sleeve. When your atty runs dry instead of pulling it up and vaping just pull it up (just have figure out how much) and it will feed into the holes then just push back down and vape. Kinda like a poor mans pump.

This sure is a quiet thread, I feel like I'm talking to myself...

Were listening. This seems like a phenomenal idea! I was about to PM you and ask you to make me one and name your price... Then I saw your location. I dont like dealing w customs, etc. I will be trying this, in the next week, and I'll let you know. Great job.

 

[kwalka]

I have almost replicated this to the T. The only problem I'm having is getting the atty in all the way. It doesnt want to slide in all the way, it stopping at about 1/8" from fitting all the way. I think the condom is making the hole too small. Its almost as if it wants to go together w/o the condom installed.

 

[kwalka]

Ok I made this this morning and it worked great! I've been using it all day and after a slight learning curve it works very good. I did have some minor leaking/seeping, but that was user error. I would highly recommend trying this.

 

[Njt07]

I have almost replicated this to the T. The only problem I'm having is getting the atty in all the way. It doesnt want to slide in all the way, it stopping at about 1/8" from fitting all the way. I think the condom is making the hole too small. Its almost as if it wants to go together w/o the condom installed.

You can also put the atty into the condom first then push through the bottom plug with the condom. Be carefully trying to pull a atty out if it's a really tight fit, I accidentally ripped a Cisco 306 bridgless top piece off of the base cause I rammed the atty in... Oh well it was getting old anyway.

 

[Njt07]

Quick update, I'm still using my original I made, I found that the holes in the sleeve can close up a bit after a while so I just re punch them when I'm refilling every now and then.

 

[kwalka]

You can also put the atty into the condom first then push through the bottom plug with the condom. Be carefully trying to pull a atty out if it's a really tight fit, I accidentally ripped a Cisco 306 bridgless top piece off of the base cause I rammed the atty in... Oh well it was getting old anyway.

I actually had to use a hammer to get it thru. I set it on the void of a pair of Visegrips, then used a pad, as not to damage the atty, beat it in w a hammer. After 3 hrs of use, somehow I killed the first atty. I was able to remove it by hand and install the new one with just my bare hands.
I must say I love this mod, I cant believe this has not gone viral!

 

[Drottwiler]

Subscribing to this thread as soon as I have time I'm trying this.Ty

 

[wyetterp]

Thanks for sharing. Great idea.

 

[Njt07]

No prob guys thanks to MWA for getting me onto this idea in the first place! Hope you guys enjoy it as much as I do, if you have improvements please post here! I'm still debating if I should try this with a 357 lol but I can't figure out a sleeve for it.

 

[kwalka]

I have 2 Genesis' coming so I have a few diff attys I want to try this with. I had great success w the 306. I am going to try w a 357, but I am going to attempt w a cheap 510 atty first. Thanks again man, its so nice to head out and have this thing on board for the whole day.

 

[Njt07]

Hey good luck with a 510, what are you gonna use as a sleeve? I contemplated using a condom on the outside with an x cut into it over the holes, but I'm not sure how well it will feed that way. My other thought would be to use a cut 510 tube and connect the two tubes with a carto condom, prob with that is the tank would have sit quite a ways above the mod to allow it to feed the entire tank...

 

[kwalka]

I haven't thought that far ahead yet Well I guess I have I just have no clue yet.

 

[kwalka]

Hey good luck with a 510, what are you gonna use as a sleeve? I contemplated using a condom on the outside with an x cut into it over the holes, but I'm not sure how well it will feed that way. My other thought would be to use a cut 510 tube and connect the two tubes with a carto condom, prob with that is the tank would have sit quite a ways above the mod to allow it to feed the entire tank...

I have an HH 357 long barrell. I am thinking if I cut the tank tube down about 3/16 of an inch, the whole atty will fit thru. I will start with a small hole in the side of the atty wall, inside the tank, with my dremel and enlarge it until its at the right size. What do you think of that?
I was finding that 2 holes was flooding my 306s.
If the HH does not end up working I can just put a sleeve over the hole and still be able to use it normally.

 

[Njt07]

the only problem I had was if I didn't have the sleeve on the 306 then it would flood if sitting on the table...

 

[kwalka]

the only problem I had was if I didn't have the sleeve on the 306 then it would flood if sitting on the table...

I use 90% VG juice so I think with 1 hole the exact right size I may be able to get away with it. We shall see.

 

[Njt07]

Good luck! Btw I'm thinking about switching out the plastic 306 "sleeve" with a cut off 306 carto tube, I didn't know I had one but I just found it! I'll post how it goes once I get home and get some holes in it without deforming it.

 

[kwalka]

Good luck! Btw I'm thinking about switching out the plastic 306 "sleeve" with a cut off 306 carto tube, I didn't know I had one but I just found it! I'll post how it goes once I get home and get some holes in it without deforming it.

What are you talking about? You lost me there. Maybe I'm having a brain fart? But what is a 306 carto tube?

 

[Njt07]

You know 306 cartomizer with filler. I'm going to cut the tube off, drill some holes and use that instead of the plastic 306 sleeve. I think they have the 306 cartomizers at avidvaper.

 

[Fraser Soderstrom]

who says ya can't drip and drive this mod is great i love dripping on a 306 and can't on the road this fixes that problem with 7ml of tasty juice. and it took me all of ten minutes to throw together. Great easy mod.

 

[Njt07]

Glad you like it, truthfully though I have been using a vivi nova 2.5 and Phoenix BC 3ml, my atty tanks have been collecting dust this last couple of weeks.