306 LR atty

[VPJUNKIE510]

I recently just purchased two Lr 306 atty's and two regular 306 atty's. When I first got them in last week I checked made sure they worked, and perfect no DOA's.

I then took one Lr 306 and threw it on my riva 650 mah, and well noticed it's not realy staying wet. Now I know it burn's hotter so the juice is going to burn up quicker but I am getting around one to one and a half pull's on it before I get a burnt taste. I thought maybe it need's to be broke in so I get the taste add some more, get the taste add some more. Well it's almost a week and still them same thing?

One thing I noticed when I am adding the juice it's not realy sitting by the bridge and it's not leaking out the bottom. so where is the juice going? This is the first time I purchased 306 from Litecig I wanted to try a new store. I usually get them from COV and I have never had a problem like this. Am I doing somthing wrong.? When I purchased these atty's I also purchased a green drip tip that I am using with it, I haven't bothered changing the drip tip because it's not leaking.... Can some one help me figure this darn thing out. and would it be recomended to try the other 3? I know sometime's atty's can be tricky thus the reason why I am not giving up.

If anyone has any idea's to what is going on pls let me know. My atty need's some help. I think I am gonna try the other one's tomarrow but I am just so caught up on this one and trying to get it to work right I will probly forget. I am gonna need a reminder.

 

[ukeman]

the juice goes down into the cylinder... it takes about 3 or 4 drips; i like to put a couple drips on the wick, and one on each side of the bridge.
they should get just a few to maybe 4 or 5 vapes (if i'm lucky) before it's time to reload...

 

[VPJUNKIE510]

the only problem it's almosty been a week and it's got that burnt taste, after the first hit, it's got that burnt taste again.

 

[ukeman]

my guess is that you are not a 1.5 Ohm vaper.... neither am i..... i would get myself some EM LR 510, Ikenvape 2.0 LR 510, or the Iken LR 2.0 306 ...
If i'm right and you need a cooler vape, do yourself a favor and get an Iken 801 Mini for a mind blowing vape (when the Ikens are back in stock)... Iken has adapters too.

the only problem it's almosty been a week and it's got that burnt taste, after the first hit, it's got that burnt taste again.

 

[FeistyAlice]

I've been using several Cisco LR 1.5 (1.5 ish and a little above) and two Iken LR 306 (haven't measured) for several weeks now on my bottom fed Reos. For the juices I've been using they have been perfect. Friday I switched over my juice to FSUSA Hopscotch 70pg/30vg with a few drops of PGA added for TH. All of the LR 306 were burning up the Hopscotch and quickly creating the burnt taste after one or two tokes. I can usually go >6 tokes on one bottle squeeze using several of the juices I'm vaping lately, most 100% or near VG juices.

I switched out to an LR 510 ~2 ohm and it made all the difference in the world. So it could be the juices you are using with the LR atty. I've used several other 70pg/30vg and even 100% vg juices without the burning but the Hopscotch just needs higher ohms for the best vape.

I currently have six LR 306, rotate them and usually get about 24 hours of good vaping before cleaning them by boiling and a very careful dry burns. Most of my high vg juices and my chain vaping gunk up the LR attys pretty fast. I've had four of them for a month or so and they are still as good as new or even better with the frequent boilings. I may just stop dry burning them, every cleaning, as they really don't seem to need the dry burn after boiling, unlike other attys. I may still do a dry burn every week or so just to get the wick extra clean.

BTW... I boil them in filtered water (Brita Pitcher) but run hot tap water into the tea kettle for a rinsing. I used to use boiled filtered water for the rinse but it doesn't seem to make much difference which I use.

Alice

 

[Timothy Cullen]

well 1 question number one did you prime it becuae cisco atomizers come with no primer and no matter how much juice you drip if you dont prime it it wont stay wet becuase when i clean mine if i forget than its about useless till i prime again

 

[shawnp1]

please try to refrain from promoting other sellers and their products in our forum. thank you

 

[ukeman]

srry, my bad...not thinking; and sure you have altrnate options

 

[shawnp1]

its ok, i just like to keep it about litecig in here as much as possible

 

[ukeman]

thanks, litecig has some real quality products... can you tell me if you have any 510s' that are in 1.7 to 2.0 range vs the Joye lr's?

 

[hairball]

VPJUNKIE...4-5 drops to start with. The juice goes down inside it. It won't leak. litecig has the best by far and the cheapest price on these that I could find. LR's will burn through your juice faster. As soon as you get a flavor loss, add a few more drops. I actually find it hard to flood these and I vape the heck out of them. I use mine on and Icon V1.1 to simulate 5v vaping. Awesome hardware.

 

[shawnp1]

the lr 510 atties that arent premium ones are roughly 1.7 ohm

 

[ukeman]

thanks just what i want for most of my 3.7's

the lr 510 atties that arent premium ones are roughly 1.7 ohm

 

[ukeman]

those must be your "Expert" LR 510's ? no wonder, out of stock...
please let us know when they will be in...

the lr 510 atties that arent premium ones are roughly 1.7 ohm

 

[VPJUNKIE510]

my guess is that you are not a 1.5 Ohm vaper.... neither am i..... i would get myself some EM LR 510, Ikenvape 2.0 LR 510, or the Iken LR 2.0 306 ...
If i'm right and you need a cooler vape, do yourself a favor and get an Iken 801 Mini for a mind blowing vape (when the Ikens are back in stock)... Iken has adapters too.

I will deff give it a try I never vaped 801. I am a bit broke right now maybe in a few week's I can try mixing it up. But I thought I liked the warnm vaper you might be right. I just don't remember ever having this taste, it's a bit less today I hooked it up to a bottom feeder and just kept it as wet as possible

 

[VPJUNKIE510]

so today is my second day of straight bottom feed and keeping soaking wet. It is perfect, iit just might have taken longer to break in then the other one's I have used but now it work's great. I am so happy I didn't just toss this in my junk box and give up on it.

 

[VPJUNKIE510]

So since I got the Lr 306 atty working properly I have maintained it by a clean every other day, I don't flush it completely and only dry burn a second or two and this is now working like it's brand new even by the time I get ready to clean it is still hitting like it just got out of the wrapper. this is by far the best 306 I have picked up thank's litecig. I know it's basically the luck of the draw but I think it also has to do with storage from vendor's and the user