901->801 how to

[funkybozu]

firstly you need to cut your dead 901 .use a pipecutter does a great job, you should cut about 15mm from the bottom

pull out the inner part of the atty, leave it in while you cut,it will prevent the atty sleeve from bending.
you might need to wipe the inside down. i spray some brakedust spray then wipe it down

just push your male 801 connector into the sleeve
it goes in pretty easily, but once in it stays in

get a brass nail 22mmX1.6mm
1.7mm is better but i couldn't find the nails
so i coated the nail with leadless solder to get it to the right width
then cut the nail to the length of the closed adapter
i cut the nail so it waas practicly flat with the middle part of the connector on both sides

solder both end to block and make the nail connect perfectly

all you need to do now if file down the excess solder and make incisions to let airflow in the 801 connector
i use a router, makes thing really easy
there your done!

 

[imeothanasis]

Thanks funly, nice job my friend

 

[Di]

very nice, 30 of those please, ---------

 

[Stormynights]

Funky, if you will post this in the modders section I will get it sticky.This is wonderful instructions. Even I can do this. Thank you so much.

 

[funkybozu]

oki stormy
thats cool

er i posted this in the atty mods, made more sense in there lol
sinse you have a comprehensive link thread in the modders forum

 

[funkybozu]

you can optionally use Ciscos idea and buy for 2~3$ a 901 manual batt charging adapter
and just pull the 901 male connector out and then either resolder a 801 male or 510 female

personally i find them a bit long so i would take a pipe-cutter to them and use the nail method since it plugs the hole and makes the adapter drip friendly

 

[Stormynights]

oki stormy
thats cool

er i posted this in the atty mods, made more sense in there lol
sinse you have a comprehensive link thread in the modders forum

Comprehensive link? Did I miss something? I will put the link in the tutorial section and get this sticky in the atty mods. Thank you.

 

[funkybozu]

very nice, 30 of those please, ---------

pmed ya Di

 

[funkybozu]

Comprehensive link? Did I miss something? I will put the link in the tutorial section and get this sticky in the atty mods. Thank you.

lol the thread you made for the tutorials, i though it was a great idea

 

[Stormynights]

lol the thread you made for the tutorials, i though it was a great idea

We are supposed to have a new tutorial section this fall. We are just trying to keep things organized so nothing gets lost. Thank you again for your contribution. It will come in handy for a lot of people.

 

[tribalmasters]

Ok I have the lead free solder, the brass nail somewhere and plenty of atomisers to use but sadly, I haven't got a router or any skill heheee! Perhaps I would manage to make one of these wonderful adapters if I tried but I'll leave it to the experts

 

[Vaporer]

Well done.
2 thumbs up!

 

[Rainy]

Ok I have the lead free solder, the brass nail somewhere and plenty of atomisers to use but sadly, I haven't got a router or any skill heheee! Perhaps I would manage to make one of these wonderful adapters if I tried but I'll leave it to the experts

Thanks Tribal for stating that this is an adapter. I've been watching the thread hoping to find out what it is. It is very interesting to watch but just couldn't understand what I was looking at.

 

[Stormynights]

Ok I have the lead free solder, the brass nail somewhere and plenty of atomisers to use but sadly, I haven't got a router or any skill heheee! Perhaps I would manage to make one of these wonderful adapters if I tried but I'll leave it to the experts

Do you have a Dremel? I use a Black and Decker rotary tool. It is better than the Dremel and a lot cheaper. All of the Dremel attachments fit it perfectly. Don't give up without trying. You just might surprise yourself.

 

[Di]

Do you have a Dremel? I use a Black and Decker rotary tool. It is better than the Dremel and a lot cheaper. All of the Dremel attachments fit it perfectly. Don't give up without trying. You just might surprise yourself.

I have my dremel out and ready to go,

I am going to give it a go tomorrow,
I will let you know how I went tomorrow night,

It will either be a roaring success,
or a screaming failure,

either way it will be fun for an hour or so -- ha ha

wait for it guys, ---- place your bets here -- ha ha ha 8-o

 

[Stormynights]

I have my dremel out and ready to go,

I am going to give it a go tomorrow,
I will let you know how I went tomorrow night,

It will either be a roaring success,
or a screaming failure,

either way it will be fun for an hour or so -- ha ha

wait for it guys, ---- place your bets here -- ha ha ha 8-o

Oh you go girl. You will be surprised what you can do. Believe me the hardest part will be getting started. Even if you screw up your first attempt you will learn something and get it right on the second go for sure. At least this is how I do it.

 

[Di]

Oh you go girl. You will be surprised what you can do. Believe me the hardest part will be getting started. Even if you screw up your first attempt you will learn something and get it right on the second go for sure. At least this is how I do it.

OH I am gonna do it----
the hardest part for me will be cutting it at first==
after that it will be a piece of cake, -----

bets in now please --------- 8-o

 

[Stormynights]

OH I am gonna do it----
the hardest part for me will be cutting it at first==
after that it will be a piece of cake, -----

bets in now please --------- 8-o

You are right about the cutting being the hardest. Putting this together is nothing hard at all thanks to these great instructions. I bet you can do it.

 

[Di]

You are right about the cutting being the hardest. Putting this together is nothing hard at all thanks to these great instructions. I bet you can do it.

I bet I can too -----

I will come here tomorrow night and brag about my new
801 adapter, ---- ha ha ha ---- we hope -- 8-o


aaaarggghh --- what about the soldering tho-- I cant so that -----
oh wait thats what hubby is for -- yes ???

 

[Stormynights]

I bet I can too -----

I will come here tomorrow night and brag about my new
801 adapter, ---- ha ha ha ---- we hope -- 8-o


aaaarggghh --- what about the soldering tho-- I cant so that -----
oh wait thats what hubby is for -- yes ???

You can do that girl. It isn't hard. You may not even have to if you have the right size nail. Don't touch the iron to see if it is hot enough though. 8-o

http://www.e-cigarette-forum.com/forum/modders-forum/22122-how-solder-video.html


Watch this video,fire up the iron and get going. When you are done post the pictures. You will be amazing.