A little googling session

[zer0ith]

Ya i saw that one too but completely disregarded it as a working design, look at where the wick was, it might work very well thou, who knows.

Makes me want to grab one of my Visions and trim the wick to see if there is any difference.
Hmmm.... I might just do it.... Unless mindfield beats me to it

Anyways.
The only advantages I see to these is the cone type shape that would force the juice towards the coils. But if you don't tilt your PV when taking a hit I don't think it would work very well.

 

[Mindfield]

Ya i saw that one too but completely disregarded it as a working design, look at where the wick was, it might work very well thou, who knows.

Makes me want to grab one of my Visions and trim the wick to see if there is any difference.
Hmmm.... I might just do it.... Unless mindfield beats me to it

Anyways.
The only advantages I see to these is the cone type shape that would force the juice towards the coils. But if you don't tilt your PV when taking a hit I don't think it would work very well.

The extra wick below the cup line is really just for soaking up juice when it gets low. It doesn't really work all that well though because you can burn through juice far quicker than that wick can draw it up to the coil from the bottom, so really, it's just wasted wick, so the little stubby wick in that new Vision will probably work just fine. I'd like maybe half an inch more perhaps, just to make sure it hits the wall on either side (because you know there is going to be some variance in manufacturing where some will have a slightly lopsided wick; it's inevitable as nothing is ever perfect) but that's about it. As a design concept it probably works just as well as a regular Vision.

 

[therealcmac]

The extra wick below the cup line is really just for soaking up juice when it gets low. It doesn't really work all that well though because you can burn through juice far quicker than that wick can draw it up to the coil from the bottom, so really, it's just wasted wick, so the little stubby wick in that new Vision will probably work just fine. I'd like maybe half an inch more perhaps, just to make sure it hits the wall on either side (because you know there is going to be some variance in manufacturing where some will have a slightly lopsided wick; it's inevitable as nothing is ever perfect) but that's about it. As a design concept it probably works just as well as a regular Vision.

Looking forward to a review

 

[Switched]

It would be interesting to see whether those lava tubes are oem or complete knock-offs.

Good portion from alibaba are not OEM

 

[Song]

Whats oem really, a portion of them are manufacturers and some are resalers and scammers. Considering that the original manufacturer of the lavatube isn't all that great in the QC department to start with getting the item from some other manufacturer might be just as good or better. But ya all the mini lavatubes that where linked aren't from the original manufacturer of the lavatube.

 

[Switched]

Once upon a time it was a little easier, now waaaaaaaaaay more difficult. Perhaps I should have use most instead of a good portion.

 

[cactusgirl]

Wow, what a coincidence. Just got an E-Mail from GotVapes showing that they got a couple new Visions in, including what they call the Vision Stardust. Look familiar?

Hahaha, that's so funny!

 

[VapesAlot]

the koreans are always looking for ideas to make money off of us, most look really cheap and knock offs made of plastics.

 

[Spac]

Wow, what a coincidence. Just got an E-Mail from GotVapes showing that they got a couple new Visions in, including what they call the Vision Stardust. Look familiar?

Hmm. This looks kinda neat. GotVapes has a vid of it too on his site. Might be worth a try. It certainly looks different and a bit more sleek on an eGo battery.