I open the cap, put the liquid in the (now) full open Depot, and close the cap. I don't need any tools, i put the liquid direkt from the bottle to the depot. For the baby-atty you should not use 250ml Bottles, because that like filling up a straw 
- Status
New atty pulser programm
I got out my old version of Takterprogrammes revised or written for the new evaporator is a fundamentally new program.
Now the steam setting can be adjusted with only one button in 10 steps. Since I personally am not a fan of double clicks, I have implemented it differently.
As a special gimmick:
The steam-power-shot function
If you have set stage 4, but just want a kick, then you will need during the whole of steam only put away yourt finger and put again (like a klick) and you've got a short full power thrust, followed by stage 4 extension. Thats kicks hard!
As one asks from the adjusted strength ore how to change strength?
1) push button and switch on.
Now the LED will blink first times as often as the level is set in memory. At level 4 that is 4 times.
If you want to change anything, you just take away from the finger to key.
If you want to reprogram, then, let the finger on the button.
After a second, fast flicker (as a warning that now is equal to the programming mode begins), it then flashes once every second. Each flash means 10% more power. Want to level 5 so you take just after the 5th time flashing the finger away and you're level 5 saved. Goes completely simple, its KISS . (KISS = Keep It Simple Stupid. One of the main guidelines of the development)
The program I put in here sometime soon. Right now, the program maintains, a few other things elemtar for the new evaporator , which make for genisis and other evaporator no sense, but are the new imperative. Therefore, the code fits neither the genisis, nor to the previous circuit.
The new evaporation to position 2 like a PEN. This is good because it takes so little power. Position 10 is nonsense and a power-hungry. I stand at 4-5.
Video:
On the video you can see how I can reprogram just from force 3 to 5.
This case is still with 3 sensors but only one is operating. So can not mess up. Instead of the sensor you could also take a key.
Sorry, 80% google translated.
I got out my old version of Takterprogrammes revised or written for the new evaporator is a fundamentally new program.
Now the steam setting can be adjusted with only one button in 10 steps. Since I personally am not a fan of double clicks, I have implemented it differently.
As a special gimmick:
The steam-power-shot function
If you have set stage 4, but just want a kick, then you will need during the whole of steam only put away yourt finger and put again (like a klick) and you've got a short full power thrust, followed by stage 4 extension. Thats kicks hard!
As one asks from the adjusted strength ore how to change strength?
1) push button and switch on.
Now the LED will blink first times as often as the level is set in memory. At level 4 that is 4 times.
If you want to change anything, you just take away from the finger to key.
If you want to reprogram, then, let the finger on the button.
After a second, fast flicker (as a warning that now is equal to the programming mode begins), it then flashes once every second. Each flash means 10% more power. Want to level 5 so you take just after the 5th time flashing the finger away and you're level 5 saved. Goes completely simple, its KISS . (KISS = Keep It Simple Stupid. One of the main guidelines of the development)
The program I put in here sometime soon. Right now, the program maintains, a few other things elemtar for the new evaporator , which make for genisis and other evaporator no sense, but are the new imperative. Therefore, the code fits neither the genisis, nor to the previous circuit.
The new evaporation to position 2 like a PEN. This is good because it takes so little power. Position 10 is nonsense and a power-hungry. I stand at 4-5.
Video:
On the video you can see how I can reprogram just from force 3 to 5.
This case is still with 3 sensors but only one is operating. So can not mess up. Instead of the sensor you could also take a key.
Sorry, 80% google translated.
Last edited:
Ouch. That translation hurts a little, but I think I see what you mean. It's variable voltage, which works electronically instead of mechanically. Also, you can get a little temporary boost if you want an extra kick once in a while. I have to say, that's pretty slick.
With genisis, you don't really need to adjust the power because you tinker until you get the right feel for you, but apparently this works well with the new atty (or it could be used with standard chinese atties) to have an easy to use, electronic voltage adjustment.
Very cool Raidy! Now I need tog get my genisis built before I fall too far behind.
With genisis, you don't really need to adjust the power because you tinker until you get the right feel for you, but apparently this works well with the new atty (or it could be used with standard chinese atties) to have an easy to use, electronic voltage adjustment.
Very cool Raidy! Now I need tog get my genisis built before I fall too far behind.
Raidy, this look great. KISS is the best way to design. Looking forward to seeing this new program at work together with the new atty design. Great things! Thanks for keeping us all in the loop on your progress.
I am very much looking forward to the new atty. I will definitely be buying one.
Sent from my DROIDX using Tapatalk
Sent from my DROIDX using Tapatalk
Hi all,Raidy said the air is helping to kill our attys.Can anyone tell me a possible way to make ppf3 filter mod for a GGTS because it is sealed all except the drip tip and where the variable intake holes are placed makes it impossible to place a filter on the inside. I can make something to seal up the drip tip like a rubber stopper or cap thats held on with a o-ring type of attach,but the air holes are killin me.any ideas?
I've been thinking about the same thing. If there was a filter over the air inlet on the genesis it would sadly be better air quality while vaping but the atomizers would last longer.
Those are very cool. I'm guessing the terminator isn't the most portable PV ever. They all look like great quality. Now if only the battery technology was good enough to get 12 hours of vaping out of that nano.
Raidy, I have a question for you that I would rather not post here. If you would please PM me that would be awesome. Thanks!
Raidy, I have a question for you that I would rather not post here. If you would please PM me that would be awesome. Thanks!
Wouldn't let me respond. Hmmm what to do. Very very cool of you to respond though! Thanks! I friend requested you that might allow it but I understand if you don't want to. It is late, getting early. I must sleep now for a trigonometry exam tomorrow.
Hello everyone!
raidy, you are great engineer. Thank you for your ideas sharing. Now I go after you, trying to build my Genesis. But there is one unclear thing for me. What material is better for the upper cup, holding the heater: metal or plastic? I mean: the mesh going through the cup, so it's material could be very important if we consider heatsinking. Aluminium alloy obviously takes more heat from the mesh than, for example, teflon. And it could be sufficient. I only found out, that someone put a plastic tube in the hole for the mesh.
P.S. I don't consider a wine cork, sorry
raidy, you are great engineer. Thank you for your ideas sharing. Now I go after you, trying to build my Genesis. But there is one unclear thing for me. What material is better for the upper cup, holding the heater: metal or plastic? I mean: the mesh going through the cup, so it's material could be very important if we consider heatsinking. Aluminium alloy obviously takes more heat from the mesh than, for example, teflon. And it could be sufficient. I only found out, that someone put a plastic tube in the hole for the mesh.
P.S. I don't consider a wine cork, sorry
Last edited:
Thank you, raidy, I will follow your advice. And one more question: how do you twist the mesh? Using just fingers or around, say, thin needle? Now I'm waiting my mesh from eBay and can not imagine, how to roll 14 mm wide mesh to 2 mm cylinder without a gap inside.
And what do you think about a teflon tube instead of a glass one? Glass is too fragile...
And what do you think about a teflon tube instead of a glass one? Glass is too fragile...
Last edited:
Just use your fingers, like you were rolling a cigarette, with a little practise, you soon get the hang of it and when you get it down to 2mm you will find that there is already a tiny hole through the middle of the mesh
When I get close to the size, I start running my fingers out to the ends of the mesh while still rolling, this gets the ends just a little tighter, and I am then able to insert the mesh through the 2mm hole
Last edited:
- Status
Similar threads
- Locked
