Any HV tips from fellow ECF'rs?

[icemanx3]

Hey all,

I am receiving my Maxi RoughStack V2 today, and I plan to try 6v and 7.4v for the first time after about a year of vaping at 3.7v. Are there any good suggestions or tips I should be aware of? I assume I shouldn't use, say, a 1.5ohm LR Cisco at 7.4v

Are there any sweet spots like 6v using a 2.5ohm atty, and so on? Any tips and suggestions would be very helpful so that I don't blow my face off

Thank you!

ice

 

[Nomoreash]

Everybody has their own sweet spot but I wouldn't go below 3.0 ohm at 6v and that's even to hot for me personally at 12 watts, I prefer 3.5 ohm at 6v. Keep it wet as you will go through juice faster, enjoy.

 

[fray]

I like 3 ohms at 6v. Just a little hotter than a 1.5 ohm at 3.7v

 

[icemanx3]

Oh my gosh!!!! 6v on a LR 2.0 Ohm is freakin out of this wooooooooooorrrrrrllllld!!!!!! This thing is forcing the vapor down my hatch and blasting it out my ears!!! Wowsa!!!!!

I'm using two stacked LiFePo 3v and it's making my atty hiss and roar like an angry dragon!!!!

I'm thinking about trying 6v with a LR 1.5 Ohm Dual Coil XL cartomizer. Whattayathink? Is that ok?

ice

 

[AndAllThingsWillEnd]

I had posted almost the same thing in the newbie forums the other day. I ordered a Prodigy this morning with some dual coils and I have some standard Boge cartos that I'm saving for. I also ordered some 3.5 ohm deluxe fluxomizers from got vapes that I just ordered so once everything gets here I will update...

 

[DOAlaboratories]

i'm using a 2.5 ohm dual coil at 6.5V (VV foxy box) and loving it, but i still think a two ohm would be better

 

[icemanx3]

Ummmmm. Nope! Lol, don't try LR 1.5 Ohm Dual Coil cartomizers on 6v. Unless of course you like fire in the throat and that burnt taste! Wowsa! I wont try that again!!

ice

 

[CloudCuckooMan]

i also have a vv foxy box. I have a 3.5 atty from ikenvape that hits like a freakin beast at high voltages. i don't even use it that much i can barely handle the throat hit lol

 

[icemanx3]

Awesome feedback all! Thanks!

With a LR 2.0 Ohm atty @ at 6v, a mere 1-2 second draw is all that's necessary for a massive explosive hit! It's incredible!

ice

 

[Sedateme]

I vaped 18mg nic level on my eGo, and once I got a VV I found 18mg to be kinda harsh at high voltage with some juices. Just a heads up that lower nic level might be something to look into if you run into a harsh juice at higher voltages.

 

[icemanx3]

I vaped 18mg nic level on my eGo, and once I got a VV I found 18mg to be kinda harsh at high voltage with some juices. Just a heads up that lower nic level might be something to look into if you run into a harsh juice at higher voltages.

Definitely! Thank you...One of my thoughts right now is I can lower my nic levels from 18 to 12 easily I think when messing with 6v. One thing though, 6v and flavors are muted some. I slammed in a 18650 for some 3.7v action and can taste the yummi-ness again.

Any suggestions out there for a juice that can handle 6v @ LR 2.0?

ice