Anyone here used fasttech.
- Thread starter trouble1000
- Start date
- th_trl_thread_readers 0
- Status
Special Delivery Next Day - there are 2 options 9am or before 12 if I remember correctly - you can see the options for anything on their website
Mais oui mon ami, I have one, it's a slightly smaller version of the IPV2 uses the same SX330 board and even comes up with the Pioneer logo when you switch it on, a neat little mod if you can get it at a good price.
Lemon Bar, I wanted something I knew to be luvverly to do the initial test, and i can't put it down, I'm going to be emptying the bottle in no time.
Cheers Bob it's on sale at £80.00
It sounds a decent spec but there's that much cloned rubbish about it's safest to ask
since I'd never heard of Vaping Outlaws, the makers
I paid £60 for mine 2nd hand, if it's brand new then it's a decent price but otherwise I would look at the IPV2 which could be cheaper new
Who knows! We'll just have to wait and see!Mine too trish, but with george saying his had arrived in the uk, and were shipped a day after our`s were, i just thought that the tracking over there may have not updated.
The Hana went back - son took it to the post office and sent me a photo of the receipt. (£9.75). I uploaded the photo at the FastTech site, so they can see it's been sent and also reimburse the postage
.
Adam, don't know about the way you tell when the juice is going, I find that the temperature drops off before you lose the clouds, vaping @ 30w on mine when it is soaked right through it is quite warm and as the juice gets used up the temp goes down until you can hardly feel any heat, and if I then look at the wick it is almost dry, I'm filling the well up and finding after about 6 vapes it needs filling again - definitely a heavy drinker 
Doubt if I'll have much time tomorrow as Dulwich Hamlet are at home, so will be off to see them, so on Sunday I will try doing a build on a Kayfun Lite + that needs building on because I would like to see how it performs with that, and would also like to try a dual coil as well in something, but maybe at a later date.
Doubt if I'll have much time tomorrow as Dulwich Hamlet are at home, so will be off to see them, so on Sunday I will try doing a build on a Kayfun Lite + that needs building on because I would like to see how it performs with that, and would also like to try a dual coil as well in something, but maybe at a later date.
Mine too trish, but with george saying his had arrived in the uk, and were shipped a day after our`s were, i just thought that the tracking over there may have not updated.
Yep,mines defo at Langley Tel,arrived Yesterday.And i just checked again this morning.
Funny how the Chinese can tell me it's in England,but the English can't.
Today, mine both show: 27-11-2014 29-11-2014 Despatched to overseas (Country code: GB)
Adam, don't know about the way you tell when the juice is going, I find that the temperature drops off before you lose the clouds, vaping @ 30w on mine when it is soaked right through it is quite warm and as the juice gets used up the temp goes down until you can hardly feel any heat, and if I then look at the wick it is almost dry, I'm filling the well up and finding after about 6 vapes it needs filling again - definitely a heavy drinker
Doubt if I'll have much time tomorrow as Dulwich Hamlet are at home, so will be off to see them, so on Sunday I will try doing a build on a Kayfun Lite + that needs building on because I would like to see how it performs with that, and would also like to try a dual coil as well in something, but maybe at a later date.
Tried a 25ga build on the magma, did a 3mm coil with as many wraps as I could reasonably fit on, about 15 I think. The board initially thought it was 0.11 ohms but then after a few vapes went down to 0.09 ohms so it kind of works but I get a low ohms warning if I fire it at 40W. Not sure that this wire is going to be of much use really, as the coil is so big it takes an age to heat up at say 30W. I'll try it again later.
Also a slight annoyance I just noticed was that the battery ran down and started giving me "weak battery" warnings so I changed it out for a VTC4. Although by disconnecting the battery the board forgets the atomiser resistance so when you fire it again with the new one it will measure the initial resistance while the coil is still warm, making it slightly off I guess.
I didn't think about this but I guess you'd have to plug in the usb to charge it while you vape (as it does do that).
Read some opinions elsewhere about all this and one guy was saying a lot of sensible things that I'd agree with, but also if you're using a nickel build, don't fire it without temperature protection to make the coils glow, as it will taste off for a while afterwards. I hadn't thought that with the build I did yesterday, although I did only pulse them a little, not like holding the button down for several seconds at a time.
Anyway I guess I should stop mucking about and do something with my weekend haha
Postman deliverd mine this lunchtime Trish,so yours can't be far away.
A belated thanks Bob, I couldn't keep my eyes open any longer
Thanks George ..these two orders have been odd for tracking!
Yep same here, though still not arrived in the uk yet. Should have them early next week eh
I decided to re-coil one of my orchids today from 1.8 to 1.4 ohms. When i had the coil installed i thought i would have a quick look at the fill port. I looked at the filling hole, and could only see a slit of daylight through it, and thought that must be where the chimney is obstructing it.
So, i got my syringe just to see if it would fit through the slit, and whilst doing that a tiny bit of swarf came from inside the tank !!! So now, i have a fully opened fill hole, and filling from the bottom was a breeze. This is just a heads up really, in case anyone else comes across the same thing.
So, i got my syringe just to see if it would fit through the slit, and whilst doing that a tiny bit of swarf came from inside the tank !!! So now, i have a fully opened fill hole, and filling from the bottom was a breeze. This is just a heads up really, in case anyone else comes across the same thing.
I decided to re-coil one of my orchids today from 1.8 to 1.4 ohms. When i had the coil installed i thought i would have a quick look at the fill port. I looked at the filling hole, and could only see a slit of daylight through it, and thought that must be where the chimney is obstructing it.
So, i got my syringe just to see if it would fit through the slit, and whilst doing that a tiny bit of swarf came from inside the tank !!! So now, i have a fully opened fill hole, and filling from the bottom was a breeze. This is just a heads up really, in case anyone else comes across the same thing.
First thing I did was to take everything apart, remove all the screws and o rings,
soak everything in warm detergent and then clean every machined surface with one
of those little interdental brushes, the bottom of the basin had quite a bit of crap
when it was finished
hope so - not really a worry as we could sort of see where they were - more concerned right now abut my 92 order from Cloud House France - hopefully something can be found out on Monday.Yep same here, though still not arrived in the uk yet. Should have them early next week eh
I decided to get most of what I wanted to try in one order to eliminate a few orders with costlier postage. Idea is that I may find a few that I like enough to get bigger bottles!
I ordered a few direct from Indigo today using the 25% discount code (thanks Bob!) ...I saw they had some 'holiday' ones too! I got some Gingersnaps (ginger cookie and coffee) and Noggin (eggnog and spices), and Santa (chocolate and biscuits). Plus some Blueberry Whoopie, Shenanigans, Dawn to Dusk,
If There's a few I like, I'll try another two I thought would be good.
Apparently Santa is to be permanent because it's been so popular. Hmm ..Christmas every day
Just realised we hadn't checked the post box today ...post must have arrived without the dogs seeing him!
Got my little package of 6x10ml ones from Highbrow Vapors - excellent packing etc. - ordered last Saturday 22nd, despatched Monday 24th ...here today! That's fast I just tasted a drop from each:
Caramel Cake - Lovely: caramel and vanilla cake! Think this can be used right away too
Cheesecake Torte - lovely creamy cheesecake and no cheese taste in this one! - be good alone or mixed with a fruit, chocolate etc.
Dark Chocolate - Very nice! I think I could use this right away if I want to
Cappuccino Diablo - nice creamy coffee - promising! needs a steep
Limoncello - nice clean taste, needs a steep - be great if the flavour increases a bit.
Tiramisu - seems nice - will know better in a week.
- Status
Similar threads
- Locked
