Atomizer dripping

[sereil46]

I've been reading about dripping for to last few days. I was concerned of going the atty route when I was first looking into vaping but now I might be something to checkout. Thanks for the info

 

[Smiddy]

best dripping atty u will ever find...i guarantee it...forget the hh357 and all that garbage - CHEAP and awesome - Vape - SmartVapes 306 1.8ohm E cig Dripping Atomizer

I'm giving u pearls of wisdom here...u listening?

I finally got off my .... to get these on order and there's no black or white. Bummer. I look goofy enough smoking my APV being that its the size of the Mandingo. I cant add a pink drip tip. I hope they get more soon.

 

[Holbie]

best dripping atty u will ever find...i guarantee it...forget the hh357 and all that garbage - CHEAP and awesome - Vape - SmartVapes 306 1.8ohm E cig Dripping Atomizer

i'm givin u pearls of wisdom here...u listening?

Thanks darkhood i've been looking for advice on which atty to get to start dripping with. Just ordered two of them and cant wait to get them so I can start dripping. Been using tank systems primarily but want to be able to try a bunch of different juices and see what i really like.

 

[fourtwizzy]

best dripping atty u will ever find...i guarantee it...forget the hh357 and all that garbage - CHEAP and awesome - Vape - SmartVapes 306 1.8ohm E cig Dripping Atomizer

i'm givin u pearls of wisdom here...u listening?

Thanks for the wisdom, I put an order in for one

 

[jcco]

Thanks darkhood i've been looking for advice on which atty to get to start dripping with. Just ordered two of them and cant wait to get them so I can start dripping. Been using tank systems primarily but want to be able to try a bunch of different juices and see what i really like.

Me too, was looking to get atty's but you musta got the last ones. Their site say's it's out of stock. What is up with that?

 

[roundrock]

I second the 306 atty for dripping. It has a mesh bridge and a sealed bottom (to the juice bowl), so you don't get leaking from it and all it takes is a couple of drops through a drip tip when you sense the vapor beginning to wane. The mesh helps to absorb and hold the juice while it wicks into the coil. 306 is definitely a winner for dripping and will give you the best flavor you will ever get from your juice.

You did mean to type 3.7v mechanical mod, didn't you? 1.8 ohms to 2 ohms is where you want to be with that voltage.

What about using either standard or low ohm on my ProVari Mini? WHich is best? Also, I am getting lower ohm reports on the PV than packaging states- ex. 1.8 for 2.0 and 2.4 for 3.0.... Is there a standard error of measurement?

I've been buying Joyce 510s.

Thanks in advance.

 

[1LastShot]

Me too, was looking to get atty's but you musta got the last ones. Their site say's it's out of stock. What is up with that?

Same here :-(

 

[Holbie]

Me too, was looking to get atty's but you musta got the last ones. Their site say's it's out of stock. What is up with that?

To clarify, I thought I had ordered a 306 but I did not they are out of stock on the 306 the one I ordered is this one Dripping_Atomizer_510_1_8ohm_Stainless.html reviews still look really good and its still got the sealed center post. I hope it performs as well as the everyone is saying the 306 do.

 

[Holbie]

Got my Attys today... Dripping Atomizer 510 1.8ohm Stainless from smartvapes.com

didn't know about the primer they put on some from the factory, definitely think these had them, I opened one as soon as I got them and popped it on my VV mod but even at 3.5 it was seeming to be hot and taste metally decided to put it on one of my old inferno batts and it worked better but still tasted horrible. thanks to Ocelot I found out about the primer, rinsed it out with warm water blew it out and started dripping again... Voila! Horrible metal taste gone, now just to get the proper amount down so I'm not wasting juice out the bottom. Does anyone know of any ways to slightly increase juice capacity or is that just the nature of the beast with Direct Dripping?

Enjoying some fruit stripe Illusions from Vermillion River right now, Definitely got the bubble gum taste but could use a little more fruit IMHO

 

[roundrock]

Got my Attys today... Dripping Atomizer 510 1.8ohm Stainless from smartvapes.com

didn't know about the primer they put on some from the factory, definitely think these had them, I opened one as soon as I got them and popped it on my VV mod but even at 3.5 it was seeming to be hot and taste metally decided to put it on one of my old inferno batts and it worked better but still tasted horrible. thanks to Ocelot I found out about the primer, rinsed it out with warm water blew it out and started dripping again... Voila! Horrible metal taste gone, now just to get the proper amount down so I'm not wasting juice out the bottom. Does anyone know of any ways to slightly increase juice capacity or is that just the nature of the beast with Direct Dripping?

Enjoying some fruit stripe Illusions from Vermillion River right now, Definitely got the bubble gum taste but could use a little more fruit IMHO

Ocelot also helped me to begin dripping. It's far more ritualistic than my tanks, but satisfying in a way the cartotank doesn't provide. Using your link, I looked at your atomizer-- it has a sealed bottom, right? Is it leaking juice from the bottom?

 

[Holbie]

Ocelot also helped me to begin dripping. It's far more ritualistic than my tanks, but satisfying in a way the cartotank doesn't provide. Using your link, I looked at your atomizer-- it has a sealed bottom, right? Is it leaking juice from the bottom?

The bottom iself is sealed but there are small holes around the threading for airflow and that is where it is leaking from.

 

[Myrany]

lol it's the same as a 510 just w/o the glue and attached tube...a much better design for dripping....its the purest form of atty there is;

Darkhood I am a complete newbie to this stuff so forgive if this is a dumb question please.

I have been taking a hard look at trying to go the DYI juice route. Would this atty work for testing juice flavors so that I can adjust them as I am making a recipe?

Also I am thinking about buying a Vamo to replace my ego-c's would this atty be ok on the Vamo?

 

[Holbie]

I have been taking a hard look at trying to go the DYI juice route. Would this atty work for testing juice flavors so that I can adjust them as I am making a recipe?

Myranny - check out DIY Flavor Shack Platinum DIY kit Dawn runs the shop there and she is by far one of the best customer service people I've dealt with. There are a few different options as far as the DIY kits they all come with 6 flavors a tool box and all the bottles PG/VG/Nic base you need to make about 100ml of juice(mixed). You get to pick your flavors and if you call or e-mail she can help with some of the flavors. the one I got was 30ml of 36mg nic base (90ml of 12mg base when mixed) but like I said it is up to you strength you want.

 

[Holbie]

also yes a basic atty would work for taking a puff or two of a flavor while mixing it up... I think thats what are going to become used for unless I get the dripping down better.

 

[Riverboat]

HH357 for $6??? That's a hell of a price drop!

No....you know they are $22-$25 for a custom HH357 and they are worth it...thats how good they are!