AVS help!

[WetStick]

Thanks Imeo, she's in a better place and out of pain.

Just double checked the receipt; they are all GG-AFS-V2-Universal. Sorry, I don't know where I got AVS.

Thanks,

/wet

 

[imeothanasis]

Good for her buddy

Do they have the brass connector at the bottom Wet?

 

[buGG]

wetstick,
i believe the i7 atty is 5.2 ohms (initially intended for 7.4V). ikenvape was/is a good source for them, but they are currently out of stock. you might want to do a search for "5.2Ω" or "5.2 ohm Atomizers" and see where else they pop up. however, if this is your sweet spot and you can't find these at the moment, you should know that you can match this "vape" in watts with a 1.8 to 2 ohm atty and a single 3.7V battery. most low resistance "SLB 901s" will be between 1.6-1.9Ω and two attys in this range that i would certainly recommend are the 1.7Ω SLB 901 from madvapes or the 2Ω SLB from ikenvape. you may find that you like this setup even better for different reasons, but if not and if you can't immediately find the 5.2Ω attys for your AFS at 6V then these will at least hold you over in the meantime.

 

[HoPeFuLLL]

or 808 catos at 3.7, 6 and 6.4V. To made the hole use a screw or nail about 7mm up from the bottom. Drilling is too hard.

10x5pc Empty Disposable Capsules for KR808D-1 In 3 Colors [KR808D-1] - $45.00 : Healthcabin Electronic Cigarettes - Wholesale and Retail

 

[Rippspeed]

I only have the 901 connector now, Imeo....

what happen to the 901 connector you were suppose to get ??? Ty; try and get yourself a 510 connector and use the LR306 ... man its the freaking BOMB

 

[ImYourSalt]

Ok! It's on the wishlist, but for now, it'll have to wait until after the holidays!

I gave you a heads up on the SoCal thread...
The 2nd connector VK sent me was apparently lost by the post office.
This has been an exemplary case of, 'whatever can go wrong, will go wrong'.
Thanks to Ross and Michelle (? - sorry, it's late...), for their great customer service. Now if only the Post Office could get their act together

Anyhow... I'll mess around with it this weekend, when I have time to run to the hardware store... And send it back to you on Monday. I hate for you to be without.

muchos gracias!

 

[imeothanasis]

Guys, we have to wait for wet's response to see first what AFS he has. Maybe he has the very first ines that need a hole in the side of atty to work

 

[Rippspeed]

Ok! It's on the wishlist, but for now, it'll have to wait until after the holidays!

I gave you a heads up on the SoCal thread...
The 2nd connector VK sent me was apparently lost by the post office.
This has been an exemplary case of, 'whatever can go wrong, will go wrong'.
Thanks to Ross and Michelle (? - sorry, it's late...), for their great customer service. Now if only the Post Office could get their act together

Anyhow... I'll mess around with it this weekend, when I have time to run to the hardware store... And send it back to you on Monday. I hate for you to be without.

muchos gracias!

ty;
keep it until you get your 901 connector... When you do send it back to me and I'll send you the fuse kit I promised you ... And if you havent gotten the orings let me know I'll send them to you as well

 

[WetStick]

Hopefully the image below works. I'm sending from an iPhone.

They have a brass base that the iatty screws on to. The attys need the hole.

I lost one of the i7s last night, so I used an i3 that I had, with a 3.7v, and just don't get the vape that 6v gives me. But, it is better than nothing.

Thank you to everyone that trying to help. I appriciate it.

/wet

 

[imeothanasis]

Wet, those AFSs work with any atomizer buddy, you dont need a hole on the atty. So please buy VHV atomizers for 7,4 vape or HV atomizers for 6 volt vape

 

[SSRob]

Wet,

I sent you a response to your CRM ticket on our site...did you not get my response?

Thanks
Rob

 

[ImYourSalt]

ty;
keep it until you get your 901 connector... When you do send it back to me and I'll send you the fuse kit I promised you ... And if you havent gotten the orings let me know I'll send them to you as well

Thanks my friend. I got your PM, I will call you tonight...

 

[ImYourSalt]

so i got an O ring from Lowes. they didnt have danco brand, these are BrassCraft # 0555. the dimensions are
ID 3/8"
OD 19/32"
WALL 7/64"

I dont think it's the perfect one for the job (something with a smaller wall may be better), but i didn't have my avs with me, and just bought a few sizes. this one is close... it does the trick.

What are the dimensions for the O ring I need Imeo? The upper atomizer O ring for the mouthpiece/top cap ?

#11

Thanks!

Other than That, I have another problem. the atomizer gets flooded, and theres no more airflow. How do I correct this? can I just blow into AVS? or do i have to take it apart an clean the atomizer?

 

[Rippspeed]

the atty gets flooded right after you refill and close the top , huh Salt ???

 

[Rippspeed]

so i got an O ring from Lowes. they didnt have danco brand, these are BrassCraft # 0555. the dimensions are
ID 3/8"
OD 19/32"
WALL 7/64"

I dont think it's the perfect one for the job (something with a smaller wall may be better), but i didn't have my avs with me, and just bought a few sizes. this one is close... it does the trick.

What are the dimensions for the O ring I need Imeo? The upper atomizer O ring for the mouthpiece/top cap ?

#11

Thanks!

Other than That, I have another problem. the atomizer gets flooded, and theres no more airflow. How do I correct this? can I just blow into AVS? or do i have to take it apart an clean the atomizer?

Ty give me a call brotha ... PM me your address and I'll send you the orings tomorrow ...

 

[imeothanasis]

The o-ring that goes around the threads of the mouthpiece is 10/1 and the o-ring between the 2 caps is 9/2,5 Salt

If atomizer is flooded then blow via mouthpiece or take mouthpiece off and turn GG looking the floor so liquid will go out and empty the collector tank

I think Rip will help you, he use the 510 connector and he is very happy with it.

 

[HoPeFuLLL]

Imeos not admitting it Salt but it's pretty obvious by now no o-ring will fix it ...and you will never have a number on that GG, oh the loss. It's time to cut your losses.. The writing is on the Wall... umm, lots of other sayings..

So my offer still stands because as an X Seller I believe it is my duty to help.

 

[HoPeFuLLL]

You going to make me throw in a couple of cartos?

 

[Rippspeed]

Imeos not admitting it Salt but it's pretty obvious by now no o-ring will fix it ...and you will never have a number on that GG, oh the loss. It's time to cut your losses.. The writing is on the Wall... umm, lots of other sayings..

So my offer still stands because as an X Seller I believe it is my duty to help.

LOL... Man, I'm first in Line buddy ... Stop cutting in line Hope...
But, Hope is right though Salt ... It useless, number on a GGTS and your having issues ... I'll trade you for a GGTS with a serial number, with a clear avs tank and a regular one, with all the right orings and upgrades... Plus cash on top ... LOL

 

[HoPeFuLLL]

psst, don't forget the Cartos...