Beta AFS tank
- Thread starter wood_510
- Start date
- th_trl_thread_readers 0
- Status
ohh ok... Been wearing out the VG and loving it. I have lots of PG too though. I'm getting that leakage from that TW atty now.. May have to wait till I can get my cap update to continue using it... 
I think there was 15 of them made.
ohh ok... Been wearing out the VG and loving it. I have lots of PG too though. I'm getting that leakage from that TW atty now.. May have to wait till I can get my cap update to continue using it...
Yea the VG is fine with the larger TW atty hole. Keep on using it but switch out to the iAtty. They don't leak as much. If you hear that gurgling sound on the iAtty then you are close to flooding and time to rotate the holes up again.
I remember my first days with the AFS too. It was the end of dripping and the beginnig of vaping bliss. Glad you are loving it as much as I do.
I can't believe I don't own more of these. I hope Imeo can find it in his heart of heats and make me at least one more Beta tank for my grant and Transformer..
hehehehehe, I hear you totally. I think people who haven't tried it or those who have had difficulties actually think we are over-hyping it, but I absolutely could NOT go back to dripping now, even if you paid me.
I was a cart guy because of my job but never again... this is fantastic not having to top off or drip all day
I never even thought of that... Thanks for the hint I will do that with my next juice order
Lisa are those all yours !! 8-o
Beta AFS is the leftmost one in the pic below. Been using it constantly for the last couple of days with an i3 on my older trans at 3.7V.
Oh, and Wood, PG-based juice only in the iAtties (smaller holes). You might want a bit of VG mixed in with any TW AFS atties (bigger holes).
You can get a jug of plain PG to add to your juice and lower the nic level. That way you can have full strength for times when you may need to drip. You can add it straight to the AFS tank to cut your level down. Some folks even mix their DIY juice mixing right in the AFS tank.
Sounds good in theory, although I know nothing about this mixing stuff or where to even get the PG liquid.. Any pointers and Ideas??
Myfreedomsmokes sells PG in bulk in various sizes, I think DIYFlavorshack does too. I think Myfreedomsokes may be cheaper in bulk though.
DIY Smoke juice supplies | My Freedom Smokes
I think you can get it over the counter too, but they aren't always cheaper and they may grill you about why you want it. But as far as I know its just a humectant and isn't a controlled substance.
A lot of people will use it as a glycerin type additive for soaps and creams... at least thats what I'm i've been told.
Either way 1/2 liter for 25 bucks goes a long long ways I would guess.
DIY Smoke juice supplies | My Freedom Smokes
I think you can get it over the counter too, but they aren't always cheaper and they may grill you about why you want it. But as far as I know its just a humectant and isn't a controlled substance.
A lot of people will use it as a glycerin type additive for soaps and creams... at least thats what I'm i've been told.
Either way 1/2 liter for 25 bucks goes a long long ways I would guess.
Last edited:
My beta tank isn't working so hot on PG based juices... I checked the laser hole and it's clear... Help Vapn... hehe
O Noooooooo hate it when that happens. Well you are one of the lucky ones that can pull the tank down to cover the bottom hole and take a few short hard pulls to get juice to flow. Push the tank back up and vape away.... Careful not to flood it though. Listen to the sound of the atty. If you are using the iAtty gurgling is a sign of real close to flooding. The TW ones do it all the time so there is no telling with them, taste is the only indicator. Sometimes a few drops on the atty will help prime it a bit. Not sure how that helps but it works.....
Good luck with that thing!!!
Good luck with that thing!!!
It just doesn't seem to feed so well with my iatty. I think my liquid might be a little too thick
Yea that hole size is a bit smaller like we said to deal with the flooding issue. You should be able to put the holes down the whole time. Plus you can get a little better result to get juice flow by blocking the cartomizer holes with an o ring. 1/2"odx5/16"idx3/32" down inside the atty cap well. That will put a little more pressure on the laser hole to bring more juice into the atty. O and with the iAttie and the AFS you will need to increase your draw pressure a bit until you get juice flowing. There is a learning curve to the current AFS. hence the reason why imeo is working so hard to make a new model that deals with all these issues. Should be much easier to use. There are just so many variables with varying air pressures, varying juice viscosity, varying voltage going to the coil. It is a fine line between working well and not working good. It is a good idea to have more than one of any device so that when you are having troubles with one you can use the other while you sort out your issues on it.
I have been sealing up around the AFS with my hand and that is helping. I might just go back to my TW atty until I can pick up an o-ring suitable for the carto vents. As for having back up PV's, hopefully they will be here waiting on me when I get back from my vacation in Nashville. I'm wanting to get one of the new super slims from Rob too and a few other things. Just waiting for the new stuff to arrive... Maybe my GGT will be there as well... Any thoughts on that Imeo?? hehe... Thanks again guys...
- Status
