BF Mods by Custom-Classic

[custom-classic]

Corey, I gave BH the links to the posts on here for his mod. He is very excited to receive his CC this week!

Aha! So it was you who referred our new friend this way!

Thank you, Peng! BH has been a real pleasure to deal with. I just dropped his SSCC at the PO a couple of hours ago.

You're the best!



Great pichers comin' in this mornin', as well! Just awesome!

 

[penguiness]

Aha! So it was you who referred our new friend this way!

Thank you, Peng! BH has been a real pleasure to deal with. I just dropped his SSCC at the PO a couple of hours ago.

You're the best!



Great pichers comin' in this mornin', as well! Just awesome!

I won't take the credit for it. It was several of us posting pictures, I think

 

[custom-classic]

And she's modest!!!

Thanks to everyone involved, then.

 

[Dextrose]

That is a very cold looking CC!

Cold rolled copper? [emoji6]

Sent from my HTC One_M8 using Tapatalk

 

[The.Drifter]

Acquired a Ti Pancake rda from Nathan tonight to make my Ti-CC all matchy-matchy

 

[Train2]

schaweet...matchy matchy!

Acquired a Ti Pancake rda from Nathan tonight to make my Ti-CC all matchy-matchy

 

[penguiness]

Acquired a Ti Pancake RDA from Nathan tonight to make my Ti-CC all matchy-matchy

What do you think of it so far?

 

[The.Drifter]

What do you think of it so far?

Liking it so far Peng Built some dual vertical coils at a slight angle to start with since that seems to be a popular build for it. It's doing pretty good for a first attempt so I'm gonna keep that build in it for now. Nathan included the coil brush so I'm still trying to figure out how to use it to make proper pancake builds with it

 

[YePsTeR]

"The.Drifter, post: 18856073, member: 172046"]Acquired a Ti Pancake RDA from Nathan tonight to make my Ti-CC all matchy-matchy

That is SwEeT!!!

 

[ghola1was]

Liking it so far Peng Built some dual vertical coils at a slight angle to start with since that seems to be a popular build for it. It's doing pretty good for a first attempt so I'm gonna keep that build in it for now. Nathan included the coil brush so I'm still trying to figure out how to use it to make proper pancake builds with it

Coil brush?

 

[penguiness]

Coil brush?

It resembles a miniature brush, but with metal teeth. Allows you to make some interesting coil twists, figure 8's, and other various combinations.

 

[The.Drifter]

Coil brush?

Yes, a little accessory to supposedly make pancake coils with

I havent a clue on how to use it, still trying to get the spacing right so it dont short out. So Im experimenting like this:

so far every try resulted in a short, so apparently Im doing it wrong.....back to more experimentation....

 

[custom-classic]

Acquired a Ti Pancake RDA from Nathan tonight to make my Ti-CC all matchy-matchy

That looks great, my man!

Nice score!

 

[inswva]

Acquired a Ti Pancake RDA from Nathan tonight to make my Ti-CC all matchy-matchy

Looks awesome, Marcus! Hope it works out for you and you can master that weird coil brush. Always a pleasure to deal with you.


Sent from my iPhone using Tapatalk

 

[custom-classic]

I just took Peng's word for it and tried these, right off the bat......

They're still in there.

 

[The.Drifter]

I just took Peng's word for it and tried these, right off the bat......

They're still in there.

Yes indeed, that was my first build in it too, but I kept staring at that little brush and now a foot of 26g wire later......I'm still trying to figure out what the atty maker was thinking ....

 

[penguiness]

Yes, a little accessory to supposedly make pancake coils with

I havent a clue on how to use it, still trying to get the spacing right so it dont short out. So Im experimenting like this:

so far every try resulted in a short, so apparently Im doing it wrong.....back to more experimentation....

You might try tightening your wire so it fits very snug against the "outside" teeth. You don't have much room in the channel to prevent your coil from touching the wall. One trick is to helping remove them when the wire is tight, is to first line the bed with two pieces of wire, keeping them straight, running them down the inside of the brush close against the teeth. When you invert the brush, you can pull straight down with those two pieces of wire which will pull the coils off the teeth. Red wires below being under the coil wire to demonstrate.

I cheated, and took an old piece of mesh, put holes in it to match the teeth. I then slip the mesh piece over the brush, wrap my coils, invert into the pancake, pull on the edges of the mesh and it pulls the coils right off the teeth. I could get some tight wrapped coils that way.

 

[penguiness]

I just took Peng's word for it and tried these, right off the bat......

They're still in there.

Sometimes simple is better. At least it was to me with the Pancake. The build you have gave me the most vapor and flavor without heating the atty up so much.

 

[The.Drifter]

You might try tightening your wire so it fits very snug against the "outside" teeth. You don't have much room in the channel to prevent your coil from touching the wall. One trick is to helping remove them when the wire is tight, is to first line the bed with two pieces of wire, keeping them straight, running them down the inside of the brush close against the teeth. When you invert the brush, you can pull straight down with those two pieces of wire which will pull the coils off the teeth. Red wires below being under the coil wire to demonstrate.

View attachment 615911


I cheated, and took an old piece of mesh, put holes in it to match the teeth. I then slip the mesh piece over the brush, wrap my coils, invert into the pancake, pull on the edges of the mesh and it pulls the coils right off the teeth. I could get some tight wrapped coils that way.

Thanks for the tips Peng There certainly ain't much room at all between the channels and the teeth of the brush. You wouldn't per chance have a picture of one successfully built using the brush? Google was of no help for me tonight

 

[ghola1was]

Google was of no help for me tonight

Me neither.