BF Mods by Custom-Classic
- Thread starter custom-classic
- Start date
- th_trl_thread_readers 0
- Status
Trying out the flave rdta on my new 26650 today and been using the hadaly on the 18650 since I got it. I think these are going to be permanent setups.
Oh, and I managed to find some cappy v4s for both mods so I'm using those now too! I love those yftk bottles, just wish they came in bigger sizes!
"I'm squonkin'!" - Clarence Carter
"I'm squonkin'!" - Clarence Carter
Guys wheres my custom classic 
I don't live in a massive town, somehow it is bounced around 3-4 post offices. I live like 10 minute drive from where they would receive it through air.
They don't even need to deliver it further than the actual post office as well, i have a locker there!
The suspense is killing me
I don't live in a massive town, somehow it is bounced around 3-4 post offices. I live like 10 minute drive from where they would receive it through air.
They don't even need to deliver it further than the actual post office as well, i have a locker there!
The suspense is killing me
I got something posted from fasttech the other day and it was here in a week,Sorry, buddy.
Stinkin' post office...
I send something valuable through and the .......s run it around the whole country!
Beautiful Mods!!! Could there be a 20700 on the horizon? I'm gonna have to start saving my pennies.
Welcome, @raineysky ! 
No plans for 20700, at the moment. I do have single 18650, dual 18650, as well as 26650 mods, though.
No plans for 20700, at the moment. I do have single 18650, dual 18650, as well as 26650 mods, though.
Love these things....
ITS HERE
I'll post pics when i get a chance, it's beautiful!
Thanks Corey
"I'm squonkin'!" - Clarence Carter
Much enjoyment! The ijoy 26650s are great as well. I was at an awkward spot with 18650s where i would sometimes need an extra battery, sometimes not, so this is a good solution. And they hit like a vtc5a! (Just did a comparison vs a shorty.)
This may be a stupid question, with the 510, it is the screw bit in the top that it adjusts with?
I've got a hadaly (clone, i have an original but it has a long journey ahead) and i can't quite get it to touch base, even with the top fully screwed in.
Loving the mod, thanks again!
This may be a stupid question, with the 510, it is the screw bit in the top that it adjusts with?
I've got a hadaly (clone, i have an original but it has a long journey ahead) and i can't quite get it to touch base, even with the top fully screwed in.
Loving the mod, thanks again!
Glad you FINALLY got her, my man!
Indeed! You can just run the 510 pin up a little to meet the atty.
Hm, i don't think i can tighten it in anymore, this atty is maybe 1mm off being flush.
It's only temporary anyway, but it has been causing some arcing on top of the mod, and i've got a small dot on the side of the mod near the atty as well.
I've cleaned the arcing off, is that normal to get arcing on the actual mod itself?
I've read Noalox can help with this, haven't been able to find it in australia.
Is something like this a good substitute? H1630 - Chemtools 50g Carbon Conductive Grease - Altronics
It's only temporary anyway, but it has been causing some arcing on top of the mod, and i've got a small dot on the side of the mod near the atty as well.
I've cleaned the arcing off, is that normal to get arcing on the actual mod itself?
I've read Noalox can help with this, haven't been able to find it in australia.
Is something like this a good substitute? H1630 - Chemtools 50g Carbon Conductive Grease - Altronics
Last edited:
- Status
