BUZZ will barely fire the atty

Status
Not open for further replies.

hamdamann

Senior Member
ECF Veteran
Verified Member
Oct 1, 2010
190
31
Charlotte NC
HI i my buzz for some reason stopped working right i try and use it and it barely will fire at all the atty will not even get hot and i dont know what the problem is i have tried to adjust the voltage but nothing it is almost new to it was Order Number: 268 Order Date: Friday, 06 August 2010
has anyone else had this problem if so please let me know i need help
 

k5blazer

Super Member
ECF Veteran
Verified Member
Oct 1, 2010
787
611
Fredericksburg, VA
HI i my buzz for some reason stopped working right i try and use it and it barely will fire at all the atty will not even get hot and i dont know what the problem is i have tried to adjust the voltage but nothing it is almost new to it was Order Number: 268 Order Date: Friday, 06 August 2010
has anyone else had this problem if so please let me know i need help

Did you get it working? Try a different atty...
 

hamdamann

Senior Member
ECF Veteran
Verified Member
Oct 1, 2010
190
31
Charlotte NC
i swapped the atties and the batteries and everything the atty will fire but not very well i had to take the wire inside and take off the strip off the covering and wrap the wire around the screw in bottom of connector i tried to up the voltage but it wont go over 3.3 volts no matter how much i twist the voltage screw i am using two cr123 batteries so i dont know whats wrong with it but it has ruined my last two days i just want it fixed i would even pay to send it back to get it fixed
 

BuzzKill

Unregistered Supplier
ECF Veteran
Nov 6, 2009
7,412
5,145
65
Central Coast Ca.
www.notcigs.com
i swapped the atties and the batteries and everything the atty will fire but not very well i had to take the wire inside and take off the strip off the covering and wrap the wire around the screw in bottom of connector i tried to up the voltage but it wont go over 3.3 volts no matter how much i twist the voltage screw i am using two cr123 batteries so i dont know whats wrong with it but it has ruined my last two days i just want it fixed i would even pay to send it back to get it fixed

SO was the wire broken ? are you using 3.7 volt batteries ?? if not this can cause it to not work right BUT it should go above 3.3 volts ! that is the problem , make sure the batts are fully charged and they are 3.7 volts
 

hamdamann

Senior Member
ECF Veteran
Verified Member
Oct 1, 2010
190
31
Charlotte NC
I got two ultrafire 3.7 volt icr 123a batteries just took them off the charger right off the charger they work fine in my ggts and omega but when i out them in the buzz they wont fire the red led comes on but very faint i also have two tenergy 3.0volt cr 123a batteries and when i put them in the buzz it wont go above 3.3 volts so im not sure what is wrong or if im doing something wrong the wire was broken but i fixed it
 

5cardstud

ECF Guru
ECF Veteran
Verified Member
Jan 1, 2010
22,746
50,647
Wash
I got two ultrafire 3.7 volt icr 123a batteries just took them off the charger right off the charger they work fine in my ggts and omega but when i out them in the buzz they wont fire the red led comes on but very faint i also have two tenergy 3.0volt cr 123a batteries and when i put them in the buzz it wont go above 3.3 volts so im not sure what is wrong or if im doing something wrong the wire was broken but i fixed it
The Buzz is made to operate on 3.7 volt batteries and it works alittle on 3volt but not very long.
I have one set of 3.7 volt batteries that only work if the right on is on top. Try stretching the spring out just a touch.
I think I would send it in to have Mike fix it if it's not working right.
 
Last edited:
Status
Not open for further replies.

Users who are viewing this thread