I have some Ce2's clearomizer on the way but need tips on viscosity pg/vg .....on the juices to use in those clearomizers..???
Ce2 Clearomizers...??
- Thread starter Guyver Gaiden
- Start date
- th_trl_thread_readers 0
- Status
Good question. I know for the previous rev (CE2 R4 beta) it was recommend to me that at around 20-30% VG was good.
Don't forget to buy the special syringe for filling.
Don't forget to buy the special syringe for filling.
cools thanx...but but 4 gots to buy syringe...will other kind of syringe with a needle besides the ones that they sell on the site will work..???
Syringes don't matter, the ones they sell on sites are just regular 1-5ml syringes, it's better to use a separate 18 or 20 guage blunt tip needles than the plastic ones they give you anyway.
I like 70PG/30VG mixtures, all pg is a bit low on vapor. I've use 50/50 from vaperite also and they work fine but clog up the coil quicker.
I like 70PG/30VG mixtures, all pg is a bit low on vapor. I've use 50/50 from vaperite also and they work fine but clog up the coil quicker.
I buy 20 gauge syringes at Walgreens for a quarter each! And the needles are extra long so it's super easy to get juice out of half filled bottles. I've been filling the CE2's with 50/50 mix with no problems at all.
Needles from CVS -easy to fill [f you can find hole in inner seal.
My problem is--NO flavor or TH after trying 3 ce2's with diff. juices on a Ego.
GOOD vapor --but thats it
My problem is--NO flavor or TH after trying 3 ce2's with diff. juices on a Ego.
GOOD vapor --but thats it
I too use 50/50. Just push in slower and they work great with great flavor. I take a 20guage needle and insert into the fill hole in the clearomizer. Then I take the syringe and fill it up then put it on the needle. Makes filling a whole log easier and the syring (1mm) will fit most bottle openings. I never could pull the juice thru with the needle attached to the syringe. Maybe because my juice is 50/50. Works great, hardly any mess. If you accidently overfill, put the cap back on, take a tissue or paper towel and blow the excess juice out from the mouth part(it will come out the bat side. If you don't then the atty can get flooded and not work. Found out the hard way.
sas
sas
Needles from CVS -easy to fill [f you can find hole in inner seal.
My problem is--NO flavor or TH after trying 3 ce2's with diff. juices on a Ego.
GOOD vapor --but thats it
I found with lower ohms I don't get as much flavor. I've tried the 2.4-2.6 and the 2.8-3.0, and I love the 2.8-3.0 the best. A little less vapor, but for me it doesn't get as hot and the flavor is great! There are some great YouTube videos up about how to take it apart and fluff up the wicks so more juice gets to the atomizer. Helped me TONS!
Needles from CVS -easy to fill [f you can find hole in inner seal.
My problem is--NO flavor or TH after trying 3 ce2's with diff. juices on a Ego.
GOOD vapor --but thats it
The fill holes are directly opposite of the wicking. in other words while looking down into the clearomizer you will see where the wicking come up from the tube---directly across from each other. The fill holes(2 of them) are half way between them. sometimes if you look at it and move it with the light shining on it you can see it. if not just know that is the place. Do not stick the needle where the wicking is. Unless it is not wicking properly then only very carefully to open th hole a little.
I found that if you let it set a while after filling the flavor gets stronger and with each refill better and better.
sas
I agree with this completely. I ordered 2.4-2.6 just to try it out, and it's terrible. All i ever taste is hot dry wick, I adjusted my drags and it had worked better at one time but it was a pain monitoring how i take a drag. 2.8-3.0 work the best for me also. I decided this time to get a set of 3.0-3.2 and see how those will work.
I've measured some of the non clear ce2's, and not all of them match what the resistance on the box
.Make sure you post how you like them! I'm interested to see if they're even better.
I love them and so far I am amazed at how long they are lasting. One thing I do right before I fire one up is stick a paper clip wire down through the hole on top and pull the inner seal up off the atty just a tiny bit, that really helps the wicking and pretty much eliminates burnt taste.
I believe they are the same. Sometimes vendors just package same stuff with a tiny bit different name. Does it say who makes them and the ohms?
okay thanx cause i was going to order some flux too...but if they are then ill jus stick to clearo...
- Status
Similar threads
- Locked
