Okay made one of these and have had several people ask me how I did it. It is hard to express entirely in text, so I have put it in pics too so I can express how I got her done. I know this has been done, this is how I do it, not trying to steal any idea's this is just my take on it, and a very simple way to put together a Hybrid in 30 minutes. Oh and by the way it works as well as my other premium Hybrids at 1/3 of their retail cost.
First assemble the goodies. You will need 1. Chee-chee, chinese GGTS clone. 2.AGA-t version 1 with threaded cap. 3.AGA-t 2 or any other model of aga. 4.Lead free solder 5.Pipe thread tape 6.scrap mesh 7.soldering iron.
First: Remove top cap from AGA-t version one with threaded cap. take a pair of pliers and remove the press fitted negative post.
Second: Roll up scrap mesh and insert it into non-threaded holes of atty cap. Make sure it is snug, and trim it off so it sits beneath the surface .
Third: Solder a small neat bead of lead free solder to the cap over the inserted mesh to completely occlude the hole. This will keep juice from leaking into battery tube.
Fourth:Wrap two screw thread shafts with plumbers tape, and screw them in snug. Also ensure's tight seal to keep juice in the tank where it belongs.
Fifth:Apply two insulators to the center pins and insert it. The second insulator keeps the center pin extended and provides a cusion between the positive battery connection when the atty is screwed onto the tube. The center pin will extend past the soldered sections and and srews to make contact with the battery positive post. Assemble the atomizer using the AGA-t2 top.
Sixth: Assemble a wick and coil as per usual. I used 500ss wick lightly oxidized on top, and 28g Kanthal a-1 with a 4 wrap. Comes out to 0.8 ohms.
Your atty is now ready to rock and roll! It can be used on 22mm mods, and I have used on GUS telescope. For this tutorial I chose a Chinese Chee-Chee.
This is an 18350 Hybrid. Chee is disassembled and only pieces pictured on the right are needed. Tube and top cap to the left can be set up for alternative use, set them to the side.
I chose an AW IMR 18350 battery for the excellent amp limit and performance.
//i.imgur.com/vBoSZOf.jpg[/IMG]
Choose a thoroughly awesome juice and filler up!
Pop on your favorite drip tip and have a vape!
Absolutely fantastic!! Pictured with an Ihybrid in 18350 mode, and a ZAPMAX 18650 for reference. Good pocket Hybrid here.
First assemble the goodies. You will need 1. Chee-chee, chinese GGTS clone. 2.AGA-t version 1 with threaded cap. 3.AGA-t 2 or any other model of aga. 4.Lead free solder 5.Pipe thread tape 6.scrap mesh 7.soldering iron.
First: Remove top cap from AGA-t version one with threaded cap. take a pair of pliers and remove the press fitted negative post.
Second: Roll up scrap mesh and insert it into non-threaded holes of atty cap. Make sure it is snug, and trim it off so it sits beneath the surface .
Third: Solder a small neat bead of lead free solder to the cap over the inserted mesh to completely occlude the hole. This will keep juice from leaking into battery tube.
Fourth:Wrap two screw thread shafts with plumbers tape, and screw them in snug. Also ensure's tight seal to keep juice in the tank where it belongs.
Fifth:Apply two insulators to the center pins and insert it. The second insulator keeps the center pin extended and provides a cusion between the positive battery connection when the atty is screwed onto the tube. The center pin will extend past the soldered sections and and srews to make contact with the battery positive post. Assemble the atomizer using the AGA-t2 top.
Sixth: Assemble a wick and coil as per usual. I used 500ss wick lightly oxidized on top, and 28g Kanthal a-1 with a 4 wrap. Comes out to 0.8 ohms.
Your atty is now ready to rock and roll! It can be used on 22mm mods, and I have used on GUS telescope. For this tutorial I chose a Chinese Chee-Chee.
This is an 18350 Hybrid. Chee is disassembled and only pieces pictured on the right are needed. Tube and top cap to the left can be set up for alternative use, set them to the side.
I chose an AW IMR 18350 battery for the excellent amp limit and performance.
Choose a thoroughly awesome juice and filler up!
Pop on your favorite drip tip and have a vape!
Absolutely fantastic!! Pictured with an Ihybrid in 18350 mode, and a ZAPMAX 18650 for reference. Good pocket Hybrid here.
