Coppervape BF Mod
- Thread starter Layzee Vaper
- Start date
- th_trl_thread_readers 0
- Status
They are a bit more expensive than Ft,but for those who don't want to wait,the 10ml bottles that all the diy sites sell are also exact fit.I have around 100 bottles i have picked up from various suppliers,and i use those bottles in my cv.Whenever i make a new juice,i mix in the 10ml bottles,and just pop that bottle right into the mod.
So after a bit I recommend something like this
Good flavour and clouds, can't complain! But also I made my own juice so if it doesn't have enough flavour I can just add more [emoji38]
Just made this as a hard off switch 
It's just a small piece of card that slots in between the battery
It's just a small piece of card that slots in between the battery
Just made this as a hard off switch
It's just a small piece of card that slots in between the battery
That Definitely wouldn't Fire.
Have you had Problems with just Twisting the Button to the "Off" Position?
I just like to know that if I have the mod in my pocket while I'm working all day (moving around a lot) it's not going to spin to the on position and fire
I just like to know that if I have the mod in my pocket while I'm working all day it's not going to spin to the on position and fire
I can See That.
And your Hard Off mod is a Simple Solution.
I just like to know that if I have the mod in my pocket while I'm working all day (moving around a lot) it's not going to spin to the on position and fire
Oh and yes it did rotate to the on position in my pocket, hence the backup!
Glad I also ordered 3 CV branded ones for more $$$ than the 10 pack.Oh well, only a few bucks...
I'm not sure if it has been mentioned or not but the CV bottles have a o-ring included with them, well, at least the ones installed in the device anyway. I'm not sure how necessary they are but if you are swapping bottles, it might be worthwhile to swap the o-ring as well.
Good point. I am assuming the CV kit comes with extra bottle o-rings but dunno for sure. I didn't really look to see what is in the little parts package that comes with the mod nor did I bother to open the $3 FT spare parts kits.
Ordered a brass CV kit & a silver CV kit last night.
I have no full size BF atties, Hadaly's the way to go right?
I have no full size BF atties, Hadaly's the way to go right?
I don't have one. But for a Single Coil RDA, many people have said that the Hadaly works very well.
I do own NarDa's and an O-Atty. They work Very Well if you lean more towards Flavor than Clouds.
I really like the Narda clone from Fasttech...great addy...plenty of flavor
That depends on your preferences, of course. For what it's worth, I like the NarDa: single coil, easy to wick, relatively dribble-free (in the event of a careless over-squonk), and I can shut down the airflow so it approximates an ordinary filter cigarette. I prefer Kanthal coils in the 1 - 1/2 ohm range.
Plus it's short and squat and sits right on the deck without a big gap. Works for me, anyway, and it looks good on the CV.
I don't have any Bottle O-Rings in my CV's. And I Haven't had any Leaking.
But, YMMV.
BTW - What size is the Bottle O-Ring?
I'm getting BF mechs so I'll have something stronger than a P2.5/KFL+ when our regulated OLED screens quit displaying in 10 years or so. No patience to drip every few hits.
I use dual 24ga 3mm id 6/5 wraps @ .25Ω at 69w in my Aromamizers.
Simple to wick and exactly the vape I want.
Flavor more than clouds I guess. Hadaly or NarDa?
I use dual 24ga 3mm id 6/5 wraps @ .25Ω at 69w in my Aromamizers.
Simple to wick and exactly the vape I want.
Flavor more than clouds I guess. Hadaly or NarDa?
The primary seal on the bottle is the top rim against the rubber gusset in the cap. The o-ring is just a secondary seal supposedly keeping any leakage contained in the thread area. But if the primary leaks the secondary is not going to save you.
I use the bottles with and without the o-ring. The primary seal has not failed on any so far.
I'll have to Check Out the v2 CV I got from Fasttech later today.
Because the Two v1 CV's I got directly from CV don't have Rubber Gusset in the Metal Bottle Cap.
On my V1 I had a little seepage, so I added a thin o-ring at the bottom of the threads on the bottle - that took care of it - it's been fine for months now.
- Status
Similar threads
