Coppervape BF Mod

[zoiDman]

I finely received my CP I really like the looks of it, but is there any way to increase the size of the juice hole. I have to press really hard to get the atty wet.

Don't know if the juice Hole can be made much Bigger? But one thing to check is to make sure the Clear Feed Tube inside the Bottle isn't touching the Bottom of the Bottle.

If it is, Cut Off a Very Small amount from it's length so there is a Small Gap between the Feed Tube and the inside bottom of the Bottle.

One of my CV's came with a Feed Tube that was kinda Long. And it make it harder to Squeeze the e-liquid out of it.

 

[muzichead]

@cdmcfud You need to make sure your feed tube is snipped so as to rule out its not suctioning to the side or bottom of the bottle. Below is an explanation as to how to do it...

Never cut a tube straight off no matter how close or far away from the bottom it is... It "WILL" find a way to suction itself to the side of the bottle just as easily as the bottom!! Not to mention you won't be able to squonk your bottle dry if it doesn't reach the bottom.

The tube should have an inverted V cut into it like this...l^l This will insure the tube will never suction to the side or bottom of the bottle... The tips of the inverted V should be right at the bottom of the bottle and preferably just barely touching it.

 

[Train2]

Check that the tube isn't "suctioning the bottom" of the bottle!!
You can prevent this for good by snipping it so the bottom of the tube is an angle or a "V".

Other than that, it's mostly the atty - the tube, while there ARE others with larger inner diameters - should be sufficient to allow a pretty easy squonk, if the atty has a decent hole in it.

I still never used the supplied atty, so I don't know how much resistance it might be adding, but my coppervape bottle/tube feed juice pretty smooth.

I finely received my CP I really like the looks of it, but is there any way to increase the size of the juice hole. I have to press really hard to get the atty wet.

 

[Train2]

LOL - "JINX!!""

Don't know if the Juice Hole can be made much Bigger? But one thing to check is to make sure the Clear Feed Tube inside the Bottle isn't touching the Bottom of the Bottle.

If it is, Cut Off a Very Small amount from it's length so there is a Small Gap between the Feed Tube and the inside bottom of the Bottle.

One of my CV's came with a Feed Tube that was kinda Long. And it make it harder to Squeeze the e-Liquid out of it.

@cdmcfud You need to make sure your feed tube is snipped so as to rule out its not suctioning to the side or bottom of the bottle. Below is an explanation as to how to do it...

Never cut a tube straight off no matter how close or far away from the bottom it is... It "WILL" find a way to suction itself to the side of the bottle just as easily as the bottom!! Not to mention you won't be able to squonk your bottle dry if it doesn't reach the bottom.

The tube should have an inverted V cut into it like this...l^l This will insure the tube will never suction to the side or bottom of the bottle... The tips of the inverted V should be right at the bottom of the bottle and preferably just barely touching it.

 

[benley73]

Not had that problem with sny of mine , i know it is small but has worked well for me ,

Sent from my ONEPLUS A3003 using Tapatalk

 

[zoiDman]

Not had that problem with sny of mine , i know it is small but has worked well for me ,

Sent from my ONEPLUS A3003 using Tapatalk

Were talking about the Feed Tube... right?

 

[cdmcfud]

All I've done so far is make the coils and I did that yesterday, I investigated the hose just now you are all maybe right but it was leaking like crazy from the inside top when I pulled the top off to check.
I did notice the thread was kind wacky when I screwed on the bottle yesterday but it seated tight.
I guess I'll have to start all over again.

 

[muzichead]

Its really simply to cut the hose even if its in the device. Lay the hose out on a flat surface and with a razor blade make the cuts /\ from outside corner to center from both sides and you're good to go. You can also do it with a small pair of sharp scissors too. After making your cuts, grab the piece in the center of the cut and pull slightly on it and it will separate from the rest of the tube...

 

[zoiDman]

All I've done so far is make the coils and I did that yesterday, I investigated the hose just now you are all maybe right but it was leaking like crazy from the inside top when I pulled the top off to check.
I did notice the thread was kind wacky when I screwed on the bottle yesterday but it seated tight.
I guess I'll have to start all over again.

If there wasn't a good seal between the Bottle and the Bottle Cap then the Feed Tube might not have been the Problem.

Because when you Squeeze the Bottle, it would be Easier for the Air to be pushed out than the e-Liquid to be Pushed up the Feed Tube. I'd Make sure that the Bottle and the Cap have a Tight Seal 1st. And that the Top Lip of the Bottle is Smooth and Consistent.

And if you take the Bottle and Bottle Cap off of the Mod's 510 Pin, you should be able to Squeeze the Bottle with your Thumb over the Bottle Cap's 510 end and No Air or e-Liquid should come out.

 

[benley73]

Were talking about the Feed Tube... right?

Yes my feed pin an tube works well , I did have to replace the feed pin that connects to the bottle top due to top part breaking off , but had spares so no problem really which i posted here a wk or so ago , but its not been to tight to feed mine , if it was too free flowing id of had floods ,
but i find it fine , like i say not had any problems with mine

Sent from my ONEPLUS A3003 using Tapatalk

 

[benley73]

If there wasn't a good seal between the Bottle and the Bottle Cap then the Feed Tube might not have been the Problem.

Because when you Squeeze the Bottle, it would be Easier for the Air to be pushed out than the e-Liquid to be Pushed up the Feed Tube. I'd Make sure that the Bottle and the Cap have a Tight Seal 1st. And that the Top Lip of the Bottle is Smooth and Consistent.

And if you take the Bottle and Bottle Cap off of the Mod's 510 Pin, you should be able to Squeeze the Bottle with your Thumb over the Bottle Cap's 510 end and No Air or e-Liquid should come out.

Or double check your using the Bf pin in the atty Too [emoji18] , I swapped over one an wondered why it wasnt Sqounking , then realised id not swapped over to bf pin in the rda that i had just replaced , [emoji26] easy to forget at times ,

Sent from my ONEPLUS A3003 using Tapatalk

 

[TheWestPole]

SXK NoToy clone came in while I was away. Beautifully made, so easy to build on, and takes a big coil if you want one. Did a simple 3 mm 24g Kanthal build @ ~.6 ohm. Fantastic flavor from the bottom air and smallish domed 18 mm chamber. A couple ml in and I can say I prefer it to NoPity with a big single, and it gives Origin Little competition in the flavor department, granted with the bigger coil proportionate with its chamber size. Airflow choices are great, with the maximum a restricted DTL close to the Origin Little, and adjustment as easy as can be.

One minor negative: the 510 end of the BF pin sticks up over 5 mm so there will be a ~.5 mm gap on fixed pin squonkers. Easy to grind to spec for me, but others be forewarned.

https://www.fasttech.com/p/6463900

ETA: I read back a few pages. Props to @benley73 for scooping me on this NoToy clone. Was tempted myself to try a Clapton for a first build, but wanted a closer comparison to the builds in my Origin Littles. Simple coils can certainly get great results on this one.

 

[zoiDman]

SXK NoToy clone came in while I was away. Beautifully made, so easy to build on, and takes a big coil if you want one. Did a simple 3 mm 24g Kanthal build @ ~.6 ohm. Fantastic flavor from the bottom air and smallish domed 18 mm chamber. A couple ml in and I can say I prefer it to NoPity with a big single, and it gives Origin Little competition in the flavor department, granted with the bigger coil proportionate with its chamber size. Airflow choices are great, with the maximum a restricted DTL close to the Origin Little, and adjustment as easy as can be.

One minor negative: the 510 end of the BF pin sticks up over 5 mm so there will be a ~.5 mm gap on fixed pin squonkers. Easy to grind to spec for me, but others be forewarned.

https://www.fasttech.com/p/6463900


View attachment 624845 View attachment 624847

Looks Great.

Man... I Can't Wait for mine to get back from it's side trip to Chicago!

 

[oplholik]

Mine shipped today, so maybe another couple of weeks.

 

[zoiDman]

Mine shipped today, so maybe another couple of weeks.

It would be Less if you lived in Chicago.

 

[pianoguy]

Looks Great.

Man... I Can't Wait for mine to get back from it's side trip to Chicago!

Mine came today - it was in Chicago yesterday, so it shouldn't be long now. I have it on a Pico Squeeze I ordered with it. Nice little atty, still fiddling to get it dialed in.

 

[zoiDman]

Mine came today - it was in Chicago yesterday, so it shouldn't be long now. I have it on a Pico Squeeze I ordered with it. Nice little atty, still fiddling to get it dialed in.

Cool.

I'm thinking of running it on My Pico Squeeze also.

 

[cdmcfud]

Thanks for all the advice. I cut a little vee in the feed tube and that helped with the bottle. I resealed my bottle. I was trying to type and look at the CV at the same time. Everything seems to working now.

 

[zoiDman]

Thanks for all the advice. I cut a little vee in the feed tube and that helped with the bottle. I resealed my bottle. I was trying to type and look at the CV at the same time. Everything seems to working now.

BTW - This is why People kinda Love Mech Mods. Or Kinda Dis-Like them.

Because on a Mech Mod, there Isn't much that you Can't Fix or Tune Up yourself. But on the Flip Side, there are Many Times when you Kinda have to to get things working at Tip Top performance.

 

[aikanae1]

Try the code TOAST at FT for 15% off new years day.

Sent from my LGLS992 using Tapatalk