DID style DIY TANK atomizer system
- Thread starter ricks
- Start date
- th_trl_thread_readers 0
- Status
this is a standard DID clone and should work just like the rest of them.
the single o ring in the top could possibly drive you crazy if it isnt tight enough to keep the cap on.
the single o ring in the top could possibly drive you crazy if it isnt tight enough to keep the cap on.
Last edited:
Mine is called the gen-1 from COV. Sure Vapes has them (Vulcan) with the stainless tank or you can opt for a clear tank for a couple more dollars. I think Sure Vapes has free shipping as well. I think Discountvapers sells them as the Griffin.
(On the forum here they're called the dud, didn't, diDalike etc. lol)
I liked mine so well that I bought another one. There are some issues such as leaking if not kept upright (common with most rba's).
(I posted this in another thread and I'll repeat it here)
I think they're a good choice to start with for the following reasons.
1. Proven design that works well. For example, the wick hole is close to the edge, so that when the cap is on, the air hole is probably about 3 or 4 mm from the wick. I don't know for certain, but I think that's important.
2. They come with 400 mesh and 32 ga. kanthal to get you started. You can see if you like it before ordering more, and it'll probably be a year or more before you actually need to order more. This is a biggie in my eyes because I'm poor as a church mouse, and I can't afford to toss too many things back into the unused box lol.
3. Even if you don't like ss, all is not lost. Set it up for dripping to test new juices. Very easy to do with cotton or silica or even cotton covered ss. Let's just say that I will not be buying any more 510 attys.
4. Easy to set up in different ways. For example I'm using the spin-E setup for dripping in one of my gen 1s. I would never have even tried that except for the gen-1, and I love it. Another example is cotton/ss or silica/ss hybrids wicks, whatever works for you.
5. Glass tanks are available if you want one.
Some tips that I've learned from the forum here that work for me.
1. Make your wick slightly smaller than the wick hole. Important for two reasons. 1. makes for less chance of shorts in that area, and 2. aids in wicking. ( I just learned that today. See this post. http://www.e-cigarette-forum.com/fo...tems/374459-who-vapes-100-vg.html#post8462373) If you're not using the Petar k method, just roll the wick until it fits a little sloppy. If you are going to use that method, make sure your drill bit, nail, or whatever, fits a little sloppy in the wick hole.
2. When testing, always check for resistance first, then pulse. Gently move your coils to cure hot spots. I felt like an idiot the first time I did that because I had no idea which way to move the coil. As it turns out, it's the movement that counts.
I hope some of this helps, and best of luck on whatever device you decide to get. I predict that you'll like it.
Edit: If you're looking to try out ss, then I think these are a good choice. If you're just looking for an all around good tank atty that you can rebuilt, take a look at the 'inside the drunker' thread.
(On the forum here they're called the dud, didn't, diDalike etc. lol)
I liked mine so well that I bought another one. There are some issues such as leaking if not kept upright (common with most rba's).
(I posted this in another thread and I'll repeat it here)
I think they're a good choice to start with for the following reasons.
1. Proven design that works well. For example, the wick hole is close to the edge, so that when the cap is on, the air hole is probably about 3 or 4 mm from the wick. I don't know for certain, but I think that's important.
2. They come with 400 mesh and 32 ga. kanthal to get you started. You can see if you like it before ordering more, and it'll probably be a year or more before you actually need to order more. This is a biggie in my eyes because I'm poor as a church mouse, and I can't afford to toss too many things back into the unused box lol.
3. Even if you don't like ss, all is not lost. Set it up for dripping to test new juices. Very easy to do with cotton or silica or even cotton covered ss. Let's just say that I will not be buying any more 510 attys.
4. Easy to set up in different ways. For example I'm using the spin-E setup for dripping in one of my gen 1s. I would never have even tried that except for the gen-1, and I love it. Another example is cotton/ss or silica/ss hybrids wicks, whatever works for you.
5. Glass tanks are available if you want one.
Some tips that I've learned from the forum here that work for me.
1. Make your wick slightly smaller than the wick hole. Important for two reasons. 1. makes for less chance of shorts in that area, and 2. aids in wicking. ( I just learned that today. See this post. http://www.e-cigarette-forum.com/fo...tems/374459-who-vapes-100-vg.html#post8462373) If you're not using the Petar k method, just roll the wick until it fits a little sloppy. If you are going to use that method, make sure your drill bit, nail, or whatever, fits a little sloppy in the wick hole.
2. When testing, always check for resistance first, then pulse. Gently move your coils to cure hot spots. I felt like an idiot the first time I did that because I had no idea which way to move the coil. As it turns out, it's the movement that counts.
I hope some of this helps, and best of luck on whatever device you decide to get. I predict that you'll like it.
Edit: If you're looking to try out ss, then I think these are a good choice. If you're just looking for an all around good tank atty that you can rebuilt, take a look at the 'inside the drunker' thread.
Last edited:
well over a month or two with care, most change them to freshen up but hardly ever because they are truly worn out. i have several laying around and i dont think i have actually pulled one because it was just bad or worn. just old.
go with 500 or 400 mesh and for an easier time just starting out i would go with 32g kanthal and 4-5 wraps should be right in the 2 ohm range give or take.
- Status
