I have an eGo, and lets just say... My drip tip doesn't ... drip. When I drip 2 drops in it, it stays in the drip tip. I have a little video that goes a little bit more into detail, kinda hard to put it into words. YouTube - Drip Tip HELP ME! HELP!! 
- Status
You see the little "blow" you did there at 1:03 of the video. That is the way to go. I have found this to be more true for the thicker liquids as they tend to get stuck in the drip tip and cause almost an air pocket. A slight puff of air clears it and sends the liquid to the bottom. No more juice in mouth.
I drip exclusively FWIW.
Enjoy!
I drip exclusively FWIW.
Enjoy!
Lately, I have been trying to kill off a few boxes of some cherry pre-filled tips. But normally, I drip too. That little puff of air makes a world of difference. I also keep q-tips handy for a quick swab.
Try it without the eGo cone on and see if that makes a difference...
With the cone screwed down tight.. the only way air gets into the attomizer is from the tiny gap around the top of the cone and the top of the atomizer.. your drip tip might be blocking the air passage and the liquid can't drip down.
With the cone screwed down tight.. the only way air gets into the attomizer is from the tiny gap around the top of the cone and the top of the atomizer.. your drip tip might be blocking the air passage and the liquid can't drip down.
Thanks for the help guys, I have tried the puff of air and for the most part it works. However there have been a few times that I blow a puff in and it all comes shooting out, almost like theres no airflow letting it go down into the atomizer.
What kind of tips? I have 4 delrin,and I had the same problem. I took a 3/16" drill bit through mine,and they work a lot better.Make sure to get a towel and some pliers to hold it.Also clean em out from time to time.the left over gunk will help it hold inside the tip.
I watched your video and I have to say, I had the SAME problem! No matter how much I blew on it etc. I finally broke down and bought a metal drip tip and WOW! What a difference! Seems to just roll on down instead of sticking like the plastic one. Maybe that will make a difference for you. I even like the "feel" of the metal drip tip too.
I have read about a lot of people with this problem. I agree with the poster who says to drill your opening a bit.
I have drip tips from the following vendors and have never had this experience: 510-901 Tips from NHaler-SuperT-Puresmoker a 306 tip from Digitalciggz.
I did purchase a few tips from China and all of them were too tight, the rubber gasket is too large and gets shaved as you attempt to put them in. I do not want to vape rubber, so I threw them out.
I have drip tips from the following vendors and have never had this experience: 510-901 Tips from NHaler-SuperT-Puresmoker a 306 tip from Digitalciggz.
I did purchase a few tips from China and all of them were too tight, the rubber gasket is too large and gets shaved as you attempt to put them in. I do not want to vape rubber, so I threw them out.
If you hold your PV straight up and down, yes you will probably get the juice back at yourself. Tilt it a little to help ease the surface tension as you blow lightly...like blowing across a bottle to make it "whistle".
+1 for metal.Just got an order in with metal drip tips.Rolls right down.Love it.
I am using the aluminum drip tip from madvapes and the juice goes right down. Even the shorty delrin I have sometimes the juice won't go down but the aluminum works every time.
Metal is the bomb. Slides down nice. Derlin suck bad. A blow is always good even if it goes down a little toot wont hurt.
have you tried dripping at a 45 degree angle?
hold your PV with drip tip at a 45 and then drip. this has worked for me with drip tips i thought were useless.
hold your PV with drip tip at a 45 and then drip. this has worked for me with drip tips i thought were useless.
I think the problem comes mostly with some delrins. You have to make sure you're ordering wide mouths as some delrins have that funnel like middle where it's real skinny. A tap usually works too.
ABSOLUTELY....they make the best. Their design really does make a difference. Buy a few of those and you're done
If you're having that problem, take a dremel tapered grinding stone and round off the inner ledge. The juice won't stay at the top of the tip.
- Status
Similar threads
