Two months in and still no problems. I mostly use the same tank and remove it once or twice a day to refill.
Eleaf istick connector poll
- Thread starter four2109
- Start date
- th_trl_thread_readers 0
- Status
I voted that mine is fine. I do take care of it based on what I have read and what I did to my MVP 2. I use the adapter if I have the dripper on it. That way I can brace against the adapter to pull the top cap off.
I stripped my MVP 2 510 by pulling a top cap off and off.
I stripped my MVP 2 510 by pulling a top cap off and off.
No problem with threads.....but.......... I decided from day one to put on the ego adapter and run my T3s's on it. It's been great. I don't even have to unscrew the tank to refill. Just flip over the Istick and remove only the tank section. Refill and install.
Every mod I've owned, the 510 strips out eventually. I love the idea of the stainless steel threading found on the provari so I may install some FDV connectors some day on those other mods.
The only mod that hasn't stripped out threads would be my Drawtube Mech mod which has the 510 threading drilled into the cap itself. No separate connector.
Every mod I've owned, the 510 strips out eventually. I love the idea of the stainless steel threading found on the provari so I may install some FDV connectors some day on those other mods.
The only mod that hasn't stripped out threads would be my Drawtube Mech mod which has the 510 threading drilled into the cap itself. No separate connector.
I believe there is also a problem with the grommet or gasket that is beneath the pin it seems mine got a bit smashed ....and . when that happens it wont fire because it see's a short. I never crank it up to tight and the threads are fine but I had to slip a little rubber o ring under the firing pin to keep it isolated. If that grommet is poor quality and starts to break down or tear it may bleed off some of the voltage intended for the atomizer and cause a poor quality vape or it just wont fire. Not a good thing
the pin should be spring loaded
the pin should be spring loaded
I posted later on in this thread about this...I have the same issue and needed to slip an o ring under the pin. You can use an o ring whole or cut it... and carefully loop it under the pin. if the grommet around the pin gets degraded or mashed it shorts against the body of the unit
sorry abt the multple posts here...Had the same problem and just want to make sure I get my message thru. I'm sure the pin on these sticks are getting grounded against the body because the grommet is damaged. (Or not a bit shoddy) If u can slip an o-ring under it, or cut a length of o-ring to size and loop it under the pin, it will isolate the positive pin from the negative body and fix that issue.
Yeah, Several people have had that issue. Mostly discussed in the big istick thread.http://www.e-cigarette-forum.com/fo...ion/601111-eleaf-istick-155.html#post14642279
Two iSticks both still good after a month of constant use, using Aspire Nautilus Mini on both average 2 refills per day I'm happy.
A few posts back there was a good tip, Re: filling without removing base....good one and thanks.
A few posts back there was a good tip, Re: filling without removing base....good one and thanks.
No problems for three months, then both isticks' 510s started rapid decline. Got a VS DNA30 in time to have one istick be its backup
Got one down and one still ok. Looking for something to drop the istick guts in so I can use a good 510. Heading to home depot this weekend to see if I can find a small box to use, needs to be 1/2" taller for the fat daddy 510 that I'm going to use.
Mine became "unscrewable" after 1 month. I couldn't even get the 510 connector to screw in.Ebay dealer I purchased from is out of stock, I ordered from another seller and the original seller will exchange if I pay the shipping. Istick #2 is fine so far 2 weeks in. I always use the 510 connector now. My best friends had the same issue around the 3 week mark. The place where she purchased gave her a hard time and someone walked in with the same issue and they pulled all the isticks from the store and gave her an MVP.
can you explain a little more, how do you get on o ring under the pin,, maybe some pictures would help,,Thanks
http://www.e-cigarette-forum.com/fo...ussion/473345-itaste-mvp-v2-owners-group.html
Same problem. And the solution I imagine he meant. It's what I did to mine.
Check the eleaf thread. There are some pictures there. I think it's a # 60, You just stretch it over the pin so it fits under and raises the contact point.
- Status
Similar threads
