EVIC

[Phantom27]

Can anyone show me a picture of what their LED screen looks like? I'm doing a redstone juice from mod Fuel with the NI coil that originally comes with it.

this is the settings I use for the same setup juicing RY4 double seems to work well so far i'm on cloud 9

 

[Phantom27]

That factory .5 Kanthal liked to stay inder 30-35 watts. You can push it higher, but the Lemo2 breathes so welk you don't have to.

Thanks man will definitely try it

 

[suprtrkr]

Thanks man will definitely try it

Any time, guy. YMMV. That describes the vape I like. You might like it hotter or cooler. Still, with the airflow in the Lemo 2, you can bust a medium serious cloud and grab a mouthful of flavor without pushing watts to the extreme.

 

[Phantom27]

Ok so it happened,I completely drained the ego one mega tank and it's true and tested - eVic VT will stop dry hits, it will just not vape on dry tank which is good!
However the resistance dropped from 0.2 to 0.17 (nickel coil) - dont know if this means anything, just filled the tank 90% full and see what happens... sets at 480F/50W/0.17 Ohm abit of gurgling on a full tank (i filled it half-way before), on full tank i notice it "struggling" gives off abit of a "burnt" flavour, and less cloud, will keep experimenting and report back
Edit: noticed when temp setting is at 500F it will give off bigger clouds and more flavor, still not sure why the coil resistance drops though... any ideas?

Edit 2: aha! i figured it out, instead of selecting "same coil" you select "new coil" it resets the evic and it starts working properly like before and shows proper resistance - I suspect it's something in the chip programming after a dry hit it'll go a little confused. so yea above case, if you select "new coil" it'll reset to normal - note i DO NOT have a "lock" feature on.

Back to making monster atomic clouds full of flavour

 

[Phantom27]

Any time, guy. YMMV. That describes the vape I like. You might like it hotter or cooler. Still, with the airflow in the Lemo 2, you can bust a medium serious cloud and grab a mouthful of flavor without pushing watts to the extreme.

Hey just question about Lemo2 (kendall build 0.54 resistance) original coil - when it sits for awhile and then you try and vape (settings at 20W, 3.25V, 0.53 resistance detects on evic - tester runs it 0.54 resistance btw) it'll go a very loud POP noise and spit hot burning juice right through the tube - any clue why this happens? i'm literally using mcdonalds straws taped to the lemo2 (sexy i know) to avoid burning my mouth...

 

[suprtrkr]

Hey just question about Lemo2 (kendall build 0.54 resistance) original coil - when it sits for awhile and then you try and vape (settings at 20W, 3.25V, 0.53 resistance detects on evic - tester runs it 0.54 resistance btw) it'll go a very loud POP noise and spit hot burning juice right through the tube - any clue why this happens? i'm literally using mcdonalds straws taped to the lemo2 (sexy i know) to avoid burning my mouth...

It's that huge chimney that makes it hit so good. Vapor left in the chimney after your last draw condenses and drips back down on the coil when it get cool, overloading it. Mine does it too. Turn loose of the fire button sooner, try to draw tue chimney clear, will help if not fix it completely. Get an angled or curved drip tip.

 

[Phantom27]

It's that huge chimney that makes it hit so good. Vapor left in the chimney after your last draw condenses and drips back down on the coil when it get cool, overloading it. Mine does it too. Turn loose of the fire button sooner, try to draw tue chimney clear, will help if not fix it completely. Get an angled or curved drip tip.

Thank you for the advice man!

It's actually the first draw that pops and spits out like that, not sure what you mean "draw tue chimney clear" u mean draw without the fire button pressed? tried, still pops lol - ordered a curved tip for this thing, long one, so soon i'll vape 'like a sir' (its their selling pitch lol) hopefully it wont burn a hole in me mouth. as for the draw care to expand? also do you think a different coil (like a Ni200 build on temp control) might have other results? wish i had more time to tinker with this thing... also wish it'd be possible to build on it without draining the juice all over the place when u remove the deck... ah some day

 

[suprtrkr]

Thank you for the advice man!

It's actually the first draw that pops and spits out like that, not sure what you mean "draw tue chimney clear" u mean draw without the fire button pressed? tried, still pops lol - ordered a curved tip for this thing, long one, so soon i'll vape 'like a sir' (its their selling pitch lol) hopefully it wont burn a hole in me mouth. as for the draw care to expand? also do you think a different coil (like a Ni200 build on temp control) might have other results? wish i had more time to tinker with this thing... also wish it'd be possible to build on it without draining the juice all over the place when u remove the deck... ah some day

Forgive me, I was on my tablet when I wrote and missed the typo. (WTH, I'm pretty famous for typos anyway, lol.) No, I suggest, when you are taking your last hit before setting down for a few minutes, release the fire button early and keep drawing to clear all the vapor out of the chamber and chimney, leaving nothing behind but air. It won't fix it completely, but it will reduce the condensation problem. Another idea is to go by a tobacconist's shop and get a package of pipe screens. Then punch out a tiny round one using a standard hole punch for paper. Remove the drip tip, drop the screen in the hole, and replace the drip tip. This should attenuate the drops some. I have built Ni200 coils in my Lemos for use both on my Snow Wolf and my SX mini M. It does seem to lessen the juice pops. It works like a dream on my SW, but the SX keeps shutting down with the dry coil message. I haven't had time to futz with it, but my thinking is the juice I use in the Lemo on the SX I only vape on that machine. I have one flavor I take with me in the car, and that's my car rig. It is an honest 20/80 ratio juice, and it may be too thick to wick well in the Lemo. I have heard other people complain about this before but-- unless this is it-- have not experienced it myself. The cure, of course, is to mod the tank with a dremel tool to open the juice channel a bit. The juices I vape in my other Lemo on the SW are 28/72 ratio, this being as high as I can get because both my flavors and nic juice are PG based. As I say, I have not isolated the problem, not having had time to mess with it yet. I just threw a kanthal build in a Fogger V6, zapped that on top of the SX, and am happily vaping my car juice on the SX in wattage mode. I'll message more about it if I ever get time to figure it out, but I think the screen idea and the long, curved drip tip will help a good bit.

 

[Phantom27]

Forgive me, I was on my tablet when I wrote and missed the typo. (WTH, I'm pretty famous for typos anyway, lol.) No, I suggest, when you are taking your last hit before setting down for a few minutes, release the fire button early and keep drawing to clear all the vapor out of the chamber and chimney, leaving nothing behind but air. It won't fix it completely, but it will reduce the condensation problem. Another idea is to go by a tobacconist's shop and get a package of pipe screens. Then punch out a tiny round one using a standard hole punch for paper. Remove the drip tip, drop the screen in the hole, and replace the drip tip. This should attenuate the drops some. I have built Ni200 coils in my Lemos for use both on my Snow Wolf and my SX mini M. It does seem to lessen the juice pops. It works like a dream on my SW, but the SX keeps shutting down with the dry coil message. I haven't had time to futz with it, but my thinking is the juice I use in the Lemo on the SX I only vape on that machine. I have one flavor I take with me in the car, and that's my car rig. It is an honest 20/80 ratio juice, and it may be too thick to wick well in the Lemo. I have heard other people complain about this before but-- unless this is it-- have not experienced it myself. The cure, of course, is to mod the tank with a dremel tool to open the juice channel a bit. The juices I vape in my other Lemo on the SW are 28/72 ratio, this being as high as I can get because both my flavors and nic juice are PG based. As I say, I have not isolated the problem, not having had time to mess with it yet. I just threw a kanthal build in a Fogger V6, zapped that on top of the SX, and am happily vaping my car juice on the SX in wattage mode. I'll message more about it if I ever get time to figure it out, but I think the screen idea and the long, curved drip tip will help a good bit.

Wow great idea with the screen! def gonna try and find a tobacco shop (not many of them where I live, besides i'm staying as far away from tobacco as i can (btw did you hear that in the U.K. an official study recognized that Vaping is 95% less harmful then smoking? it's official!) but yea will try the screen hehe and dont worry about typos, i'm quite famous all over fbk for gibberish typing everyone realizes i'm on my cellphone and cant type for the life of me haha welcome to the club yea i use a 30/70 pg juice (nic juice) with this thing, caramel with nic

Also I just got off the phone with a local veteran vape shop owner here, gonna share what he said which makes sense kinda maybe help us lemo2 owners::
This might be the actual coil flooding, why it pops like that and spits, so he suggested re wicking it with a new peice of cutton, said it should help. So now we're armed with an arsenal of solutions to try

I am using an Evic VT box on this little lemo2, tried playing with different wattages also, so will try and re-wick it, and report back to you unless my laptop is covered in joice oil and i slip and break my finger while mistyping haha thanks again man awesome advice

 

[suprtrkr]

A

Wow great idea with the screen! def gonna try and find a tobacco shop (not many of them where I live, besides i'm staying as far away from tobacco as i can (btw did you hear that in the U.K. an official study recognized that Vaping is 95% less harmful then smoking? it's official!) but yea will try the screen hehe and dont worry about typos, i'm quite famous all over fbk for gibberish typing everyone realizes i'm on my cellphone and cant type for the life of me haha welcome to the club yea i use a 30/70 pg juice (nic juice) with this thing, caramel with nic

Also I just got off the phone with a local veteran vape shop owner here, gonna share what he said which makes sense kinda maybe help us lemo2 owners::
This might be the actual coil flooding, why it pops like that and spits, so he suggested re wicking it with a new peice of cutton, said it should help. So now we're armed with an arsenal of solutions to try

I am using an Evic VT box on this little lemo2, tried playing with different wattages also, so will try and re-wick it, and report back to you unless my laptop is covered in joice oil and i slip and break my finger while mistyping haha thanks again man awesome advice

Any time, my friend. Holler back and let us know what, if anything, worked. If not, we'll try again