First RBA

[bman1977]

Can someone give me some advice on buying my first rba. What exactly i would need and any good sites to get it all. I'm thinking of starting to Rebuild but i'm a little over whelmed by all the information. I want the simplest build for a beginner. I'm going to continue to use my MVP 2.0.


Thanks!

 

[State O' Flux]

You need to know that the MVP2 has a hard current output limit of 3 amps. If you use Ohm's law to calculate your minimum resistance, using 11 watts and 3 amps as your known values, you'll discover that 1.2Ω is your lower resistance limit.
Going lower than 1.2Ω is a wasted effort, as you don't have adequate current to support a lower value.

The optimal wire gauge size for a single coil in the 1.2Ω to 1.5Ω range is 28 gauge Kanthal wire. With a 1.6mm (1/16") mandrel, you will produce a single coil with 10 to 12 wraps... about the longest surface area coil you can produce that will fit in most RTA or RDA atomizers.

If you buy a RDA, make sure that it has the AFC (air flow control) option for a single coil. An example in an RDA would be the Origen V2. RTAs typically have only a single air inlet and sometimes multiple (at the coil) outlets. A good single coil RTA, and perhaps the most popular of all time, are the svoemesto kayfun Lite and Kebo R91%.

Click the two sigline links below for more useful "new rebuilder" information.

 

[bman1977]

Would something like this be good to start out with?


Kayfun Lite Plus V2 Clone by EHPro - 101 Vape

 

[Smann245]

The benchmark for simple and reliable rba's has to be the Kayfun. Affordable, easily found, easy to build, performs great, lots of accessories are available... Ehpro makes really nice clones.

 

[Smann245]

Would something like this be good to start out with?


Kayfun Lite Plus V2 Clone by EHPro - 101 Vape

Perfect. I like the 3.1, but the lite is more popular. Buy it.

 

[bman1977]

Perfect. I like the 3.1, but the lite is more popular. Buy it.

Yeah. I think i'm going to go with it.

 

[BoomerFZ1]

I've started building recently as well and I've tried several (Fogger 4.1, Orchid V4, Squape and the Erlkonigin)...what I would recommend based solely on experience is something single coil to start. Like a doof, I started on the Fogger which still gives me heck. Both the Squape and Erlkonigin were very easy builds with the Erl providing the better flavor and overall ease to work with. I haven't tried the Kayfun and I think the comments I always hear about limited airflow holds me back. State o' Flux up there has you greatly covered with coiling but I found wicking MUCH easier with either Cellucotton or Koh Gen Do as opposed to cotton balls:

Amazon.com: Graham Professional Cellucotton 40 Ft. Box: Health & Personal Care

Amazon.com: Cotton Labo ORGANIC Cotton Puff Size M (200pc): Health & Personal Care

 

[Smann245]

Nice choice. There might be a slight learning curve involved in getting the build perfected, but it doesn't take long at all and once you get it sorted you'll have a very satisfying vape that is easily maintained. I occasionally use my dripper, but my Kayfun is my all day vape. Has been and will be for a long time. When you get it, the forum can help you nail down a good build for your needs pretty quick.

 

[Smann245]

The limited airflow isn't an issue for most that take mouth to lung hits. Direct lung hits doesn't seem to be what the Kayfun was designed for. For a single coil, mouth to lung device, the Kayfun is hard to beat. Just my opinion.

 

[Wolfenstark]

Would something like this be good to start out with?


Kayfun Lite Plus V2 Clone by EHPro - 101 Vape

I got that RTA for my first one and have enjoyed it. For me the airflow may be tight as I lost the two air hole screws and its good but sometimes i could do with more.

I read the lemo is good for air flow

 

[Jonner]

While I like the Kayfun (or Russian 91), I would go with a Lemo or Lemo Drop, as it's just as easy to build (or easier), good quality, lots of airflow (if you want it), and much cheaper. Good luck with whatever you decide on, lots of good info in RBA section here, or on YouTube.

 

[edyle]

Can someone give me some advice on buying my first RBA. What exactly i would need and any good sites to get it all. I'm thinking of starting to Rebuild but i'm a little over whelmed by all the information. I want the simplest build for a beginner. I'm going to continue to use my MVP 2.0.


Thanks!

https://www.fasttech.com/products/3028/10009819/1926201

I'd suggest the 22mm big dripper with glass tank option.

I am currently using mine on a 22mm deck from a flash-e-vapor because it's just got 2 posts instead of the more common type deck that the bigd comes with.

currently running mine with a 30 gauge 2.6 ohm coil at 10 watts.

the bigd is an rdta; which means it's a dripper, but includes a tank and you press on the tank to drip; so you can drip and drive.

 

[Pocha]

Would something like this be good to start out with?


Kayfun Lite Plus V2 Clone by EHPro - 101 Vape

Excellent choice! It was my first RBA too and I haven't regretted it. The EhPro is excellent (I have 3).

 

[EBates]

The FT Kayfun 3.1 ES clone has been my first RTA and my wife and I just love them. We are up to 8 of them now.
The flavor, vapor production and airflow are great, have never leaked. By far the best tank I've used.
I build 2.5 ohm coils using 32ga kanthal-a1, 9 wraps on a 1.5mm mandrel, sterile cotton for wick.
OBTW it does come with a drip tip adapter

$22.38 Kayfun v3.1 ES Styled Rebuildable Atomizer Kit (4.5mL) at FastTech - Worldwide Free Shipping

 

[aikanae1]

Im beginning to think the kanger sub ohm was designed for situations like these. Smart folks at kanger.

Sent from my LGLS990 using Tapatalk

 

[BrushyHillGuide]

While I like the Kayfun (or Russian 91), I would go with a Lemo or Lemo Drop, as it's just as easy to build (or easier), good quality, lots of airflow (if you want it), and much cheaper. Good luck with whatever you decide on, lots of good info in RBA section here, or on YouTube.

X2

The Lemo is both a Kayfun Killer and a Fogger Killer. No leaky is a big bonus. $35 average and you can own an authentic.


Sent from my iPhone using Tapatalk