Here is a real cute mod, made from a tiny flip pen/
flashlight.

http://www.freeimagehosting.net/uploads/eda67386a0.jpg
Just one screw and take this thing apart. We are going to gut it, and cut the orange pen holder in half.

http://www.freeimagehosting.net/uploads/3e537c1c34.jpg
I had a small pc board with push switches on it, so I cut it in half so I could use one switch.

http://www.freeimagehosting.net/uploads/0b4cc932d2.jpg
I cut out the battery holders and notched the existing slide switch hole to fit the new pc board switch.

http://www.freeimagehosting.net/uploads/f271a7d008.jpg
I am using the old Tr10440 battery again. I cut a battery spring to size for the negative end, and will use a piece of tin or old battery terminal for the positive side.

http://www.freeimagehosting.net/uploads/df626845f6.jpg
Now I am working on the atty connector and orange swivel holder. A little trimming and it fits.

http://www.freeimagehosting.net/uploads/d16292492b.jpg
I notch the orange swivel tube about half way around. just so I can feed a flexible wire through it.

http://www.freeimagehosting.net/uploads/ca03cccffa.jpg
Going to fit like this.

http://www.freeimagehosting.net/uploads/16602d7d42.jpg
(Skipping the tedious wiring details). I wire all connections and include the LED.

http://www.freeimagehosting.net/uploads/6fe0a3022e.jpg
And I put this sucker back together. Fits pretty good. No problems.

http://www.freeimagehosting.net/uploads/6b12f65cf9.jpg
Real tiny and feels good. Has a keychain too.

http://www.freeimagehosting.net/uploads/42b7cccbf6.jpg
There you go. Flip It...and...Drip it.

http://www.freeimagehosting.net/uploads/769b538526.jpg
flashlight.

http://www.freeimagehosting.net/uploads/eda67386a0.jpg
Just one screw and take this thing apart. We are going to gut it, and cut the orange pen holder in half.

http://www.freeimagehosting.net/uploads/3e537c1c34.jpg
I had a small pc board with push switches on it, so I cut it in half so I could use one switch.

http://www.freeimagehosting.net/uploads/0b4cc932d2.jpg
I cut out the battery holders and notched the existing slide switch hole to fit the new pc board switch.

http://www.freeimagehosting.net/uploads/f271a7d008.jpg
I am using the old Tr10440 battery again. I cut a battery spring to size for the negative end, and will use a piece of tin or old battery terminal for the positive side.

http://www.freeimagehosting.net/uploads/df626845f6.jpg
Now I am working on the atty connector and orange swivel holder. A little trimming and it fits.

http://www.freeimagehosting.net/uploads/d16292492b.jpg
I notch the orange swivel tube about half way around. just so I can feed a flexible wire through it.

http://www.freeimagehosting.net/uploads/ca03cccffa.jpg
Going to fit like this.

http://www.freeimagehosting.net/uploads/16602d7d42.jpg
(Skipping the tedious wiring details). I wire all connections and include the LED.

http://www.freeimagehosting.net/uploads/6fe0a3022e.jpg
And I put this sucker back together. Fits pretty good. No problems.

http://www.freeimagehosting.net/uploads/6b12f65cf9.jpg
Real tiny and feels good. Has a keychain too.

http://www.freeimagehosting.net/uploads/42b7cccbf6.jpg
There you go. Flip It...and...Drip it.

http://www.freeimagehosting.net/uploads/769b538526.jpg
Last edited: