Good RBA for MVP 2
- Thread starter Yankez
- Start date
- th_trl_thread_readers 0
- Status
Hey Man,
Most RBA's will work on the MVP 2.0. You just gotta make sure your coil is above...1.0 ohms(I think) I rock a Trident clone on mine and a Kraken as well. Both work great!
Good luck!
Most RBA's will work on the MVP 2.0. You just gotta make sure your coil is above...1.0 ohms(I think) I rock a Trident clone on mine and a Kraken as well. Both work great!
Good luck!
If I'm reading your post correctly, I'm thinking you aren't looking for a dripper. I love the Kayfun or Kayfun lite. They DO make some kind of a glass tank for it, but it's really expensive. You can use it with the all metal sections instead. The Squape clone from H cigar has a glass tank, but it also has a really tight draw, and is not as easy to build and wick properly in my opinion. The fogger also has a glass tank. My luck with that thing has been WAY more Miss than hit. Some people like it, but i wouldn't recommend it. I don't know of any others with a glass tank, but maybe somebody else will chime in.
Yes. Looking for one that I can fill in the morning and use all day at work without constantly having to drip
ehpro kayfun lite plus goes for around $35 on ebay. i'd go for that. an aqua clone is a bit more narrow and should fit the profile of the mvp2 a bit better and tends to go for a little cheaper
I know it's not the typical RBA with a tank.....but a glassomizer. Much like the ProTanks, they Hypertanks use same coil but are 5ml and are Pyrex. If you get the right build on a coil and use cotton (or your preferred wicking material), flavor can be really nice until you get back home to your dripper. Just a thought.
Sorry you said rba. In that case I'd go Kayfun. I've built coils down to 1 ohm but I usually build them down to 1.4-1.6 ohms. I've heard that if you go below 1 you run the risk of burning the rubber insulation on the build deck.
Sent from my SPH-L710 using Tapatalk
Sent from my SPH-L710 using Tapatalk
I use all kinds of RBAs on my MVP2. I have an EHPro Kayfun Lite, Hcigar 3.1, Fogger V2, V3 and V4, iSmoka Magoo, Prometheus and a Taifun GT. All work well with the MVP2. My personal favorite is the Fogger V2. Fasttech for $21 or Ebay for under $30. It is a bit of a pain to set up but once it is, the vape is flavorful and warm. I liked it enough to order another. Fasttech also sells replacement glass for a couple of dollars in case you are clumsy.
Try the RSST. It's cheap. It's dead easy to build on and a great starter RBA. I've used steel mesh wicks, silica, silica in mesh, and now use cotton. No problems ever with wicking using any of the materials I've tried. No flooding at all, but I drilled the airhole a little larger. Works a charm on my MVP2.
none of my mvp 2's will fire anything lower than 1.3 ohms......you must have the special one
I have fired .8 on both of my MVP's just fine. It was only to test to see if it would fire but they did
Rocket v2 from fastech its a kayfun style clone with AFC plus its only like. 25 bucks
Sent from my Nexus 5 using Tapatalk
Sent from my Nexus 5 using Tapatalk
How about the Taifun GS? might look nice on the mvp2 since it has a small diameter.
$25.39 Taifun GS Style Rebuildable Atomizer (2.7-3.0mL) at FastTech - Worldwide Free Shipping
$25.39 Taifun GS Style Rebuildable Atomizer (2.7-3.0mL) at FastTech - Worldwide Free Shipping
Kayfun, taifun, Russian, flash-e-vapor V2, are just a few that come to mind. Pick what looks best to you.
- Status
Similar threads
