H2 Clearomizer Help

[Occultation]

Hi, I bought a H2 clearomizer 2 days a go after getting fed up with constantly replacing my CE4's. Its day 3 and the taste has gone to a burnt/plastically taste. I have a spare coil, but no wicks. What do I do to fix it?! Thanks in advance.

Sent from my XT1032 using Tapatalk

 

[epicdoom]

The H2 will have a wick in the replacement coil
Replacing the coil head-

•Unscrew the base from the bottom of the clearomizer tube
•Unscrew the replaceable atomizer head
•Replace with new coil head
•Screw the base assembly back on to the tube

 

[Occultation]

And is this one going to last 3 days too???

Sent from my XT1032 using Tapatalk

 

[epicdoom]

And is this one going to last 3 days too???

Sent from my XT1032 using Tapatalk

That depends on certain factors such as what VG level your vaping, how often your vaping, are you taking big big hits. are you overpowering the clearomizer with your Battery mod. I started on a clearo and could get 2 weeks from each one then I bought an iclear 16 so I could just replace the coil instead of the whole unit as the coil was much cheaper. I'm using all RBA and rda now.

 

[Occultation]

Normal sized hits, small in some peoples eyes. No battery mod, new ego 650mah.

I read somewhere that their coils lasted sometimes a month. 3 days is just stupid. I don't need to change the whole tbjng do i!? Just the coil right?

Sent from my XT1032 using Tapatalk

 

[djsvapour]

And is this one going to last 3 days too???

Yes, most probably.

iClear16s last longer, as there are two coils.

 

[Occultation]

I cleaned it and dry burned it. Its fine again, no need to replace the atomizer yet.

Sent from my XT1032 using Tapatalk

 

[3mg Meniere]

I cleaned it and dry burned it. Its fine again, no need to replace the atomizer yet.

Sent from my XT1032 using Tapatalk

Clean and dry-burn makes them last a long time. I find that I don't need to rebuild them very often. I think this time I am going to collect a bunch before a recoiling session. The juice you are using is also a factor. Some crud up a coil faster than others. I have so many flavors in my rotation, none gets used often enough to have frequent problems.

 

[Occultation]

What does rebuilding do? Do you literally have to buy different components and rebuild them? Aha I'm so new to the technical side of vaping.

Sent from my XT1032 using Tapatalk

 

[3mg Meniere]

All you need is wick and wire, and a few other things. This is the method I use-- https://www.youtube.com/watch?v=ttsi6N2f9FI&feature=youtu.be After a while, the wire degrades to the point that rebuilding is necessary. Observation of the dry burn will show you when you need to rebuild. Don't get into rebuilding unless you have some kind of Ω meter, like what a Vamo has, or one of these:Ohm Meter and Battery Voltage Tester

 

[Occultation]

Grrr. After dry burning etc the first atomizer started leaking and gurgling and I could literally blow out the contents through it. So I replaced the atomizer (or coilhead whatever) and it has been working fine, but it has literally just started gurgling and leaking like the other! Help!

Sent from my XT1032 using Tapatalk

 

[3mg Meniere]

Order some quality coilheads, or rebuild. You can also add to the flavor wick to prevent too much juice in the heating-chamber.

 

[Occultation]

Ruining my vaping experience. I have no money at the moment and rebuilding is too technical for me.

Sent from my XT1032 using Tapatalk

 

[3mg Meniere]

Understood. Set them aside until you have the money. How can I get the L with the line through?

Evidently you have the kind I have. Take the chimney off, and add to the flavor wick. Even a couple of threads from a white 100% cotton washcloth will do.