Harsh hits all of a sudden

[brittany bell]

Put a uwell crown tank on my Evic vtc mini... after figuring out what settings/coil to use I WAS loving it.... But then all of a sudden I started getting nothing but harsh hits. Any ideas what's goin on?
I took the whole thing apart and cleaned it, got it put back together and the first few hits were back to normal but then right back to those nasty harsh/throat burning hits...... Tried switching coils too. I'm pretty bummed out that I can't figure out what I'm doing wrong

 

[Two_Bears]

Put a Uwell crown tank on my Evic vtc mini... after figuring out what settings/coil to use I WAS loving it.... But then all of a sudden I started getting nothing but harsh hits. Any ideas what's goin on?
I took the whole thing apart and cleaned it, got it put back together and the first few hits were back to normal but then right back to those nasty harsh/throat burning hits...... Tried switching coils too. I'm pretty bummed out that I can't figure out what I'm doing wrong

Sounds like you need to turn the power level down.

 

[brittany bell]

Sounds like you need to turn the power level down.

Tried that, no luck

 

[Two_Bears]

Tried that, no luck

Did you try a new coil?

Once the cotton is scorched it tastes awful till you clean it and start another coil

 

[brittany bell]

Did you try a new coil?

Once the cotton is scorched it tastes awful till you clean it and start another coil

Yeah I tried two new ones

 

[tpedwards]

Um, maybe juice viscosity. Not really sure other than that. Sorry.

 

[Hitmetwice]

The Crown comes with 3 different types of coils in the box. Each coil requires different settings on your device. The ni200 coil is very low resistance and made with nickel and must always, Always be used in temp control mode only.

Sometimes a device can Jump out of TC mode intp power mode or get switched by accident while changing settings. The result will be what you described, a burnt hit.

Whenever starting with a new coil
1. Prime it well.
2.Ensure the device is in the correct mode for the new coil. TC or wattage mode.
3. Start at an extremely low power or TC setting and increase it every few puffs.

Good vaping.

 

[brittany bell]

Did you try a new coil?

Once the cotton is scorched it tastes awful till you clean it and start another coil

Yeah I tried two new coils

 

[ENAUD]

Yeah I tried two new coils

You still haven't told what coils, what ohms the coils are, or what power settings you were trying to use, what your airflow settings are. Not much help can be offered without at least some information.

 

[brittany bell]

I've tried .25 SS coil, .5 SS, and two different .2 Ni. I've tried wattage mode with the SS coils anywhere from 30-70. Temp control with the ni 450/35w and went up from there. For airflow... I've been through half open to wide open. I kinda feel like I've tried everything

You still haven't told what coils, what ohms the coils are, or what power settings you were trying to use, what your airflow settings are. Not much help can be offered without at least some information.

 

[brittany bell]

I've tried .25 SS coil, .5 SS, and two different .2 Ni. I've tried wattage mode with the SS coils anywhere from 30-70. Temp control with the ni 450/35w and went up from there. For airflow... I've been through half open to wide open. I kinda feel like I've tried everything

You still haven't told what coils, what ohms the coils are, or what power settings you were trying to use, what your airflow settings are. Not much help can be offered without at least some information.

 

[ENAUD]

I'm not familiar with the gear, but if your juice is max VG, you might try adding a couple drops of distilled water to a tank and shake it up, this will thin the juice for better wicking, a dab will do, like two or three drops.