I just got the lemo 2 about a week ago. For the first few days it was amazing. Today I was gaping on it on the way to work and I got an intense series of lung hits. The taste wasn't burnt, it actually just tasted like it was supposed to. Then after a few more intense hits I have up on it. When I say intense think hacking and coughing. So I got home and immediately disassembled and cleaned up the tank. I then rewicked it. But now I'm still getting the same intense hot hits but with very little vapor. Help, I'm about to pull my hair out.
Help! Lemo 2 is harsh but not burnt.
- Thread starter djdepression
- Start date
- th_trl_thread_readers 0
-
- Tags
- help lemo 2 troubleshoot
- Status
You know where the build deck screws into the airflow base? Open that up, fairly certain there's some kind of moisture in there. Usually from condensation, maybe a liquid spill, in this latest case probably just wasnt quite dry after you cleaned it. Dry it well with a q-tip, check the bottom of the tank's 510 too where it screws into your mod for good measure but usually with the Lemo 2 it's inside that airflow base. It does strange things to vape that I don't fully understand the why of, but that's almost always what's wrong with mine when the vape goes all weird exactly like you described lol. Almost like you get more a stream of ultra-fine ultra-hot spray than much actual vapor lol
So I forgot to mention that when I screw the tank into my mod all the way it will show 'no atomizer' on the mod. I have to slightly unscrew it to get it to work. Would that have anything to do with it?
Tough to answer. Is it possible? I guess, if there's enough liquid there to seriously mess with the connections. Would that be my first thought, though, no... Will you tell us a lil more about your setup please? What mod are you using? What ohms are you at? Have you checked the atty on a meter or other mod, or just this one mod? That'll give us some ideas of what direction to be thinking...
Did you dry burn the coil when you re-wicked it? I'm still using the same coil that came with mine and it had been a few weeks. Good luck
Make sure your wick is not blocking or touching the wick channels. They need to be wide open on the Lemos. I do a second check after screwing on the chimney barrel. If I can't see the entire wick slot, I use a small screwdriver to push it back further.
All good advice for the quality of vape...as far as fluctuating ohms tho (what causes it to read no atty) anybody have any ideas? The only "general" thing I can think of is the mod's 510, but don't even know if OP is using a spring or adjustable or what...
That sounds like a problem with your mod, like it's shorting out. What mod do you have?
Nope I've never dry hit it. Never got a burnt hit until last night. I've rewicked it like 4 or 5 times using different amounts of cotton each time. Made sure it was well saturated and I pulse fired it to make sure it was producing vapor before I put it back together. I temporarily got it fixed last night after making sure all the connections were well dry. Then I added more juice and I went back to having the same problem. I'm using an eleaf I stick 50w. 80/20 juice and I've used 50/50 too. I noticed the little airflow adjustment part is loose too. Any more info needed? Pics of a build could be helpful, but like I said, I vaped on this perfectly for a week before this happened and I haven't changed a thing about my build. I had even cleaned it a few times before it happened. I didn't vape for a day and all of a sudden I started having this problem.
Oh and I have a .6 ohm stock coil. I did accidentally get it wet with water but that was after the problem started.
Aha, istick...see the pin inside the 510 where you screw your atty in? Get a safety pin or a straightened out paper clip or something similar, and just pry that center pin up a bit. Shouldn't take much, a mm or 2. That ought to fix it 
You could have a hot spot on the coil that's burning the juice. When you dry burn the coil does it all light up evenly? Do the ohms change when you fire it?
- Status
Similar threads
