I cannot build anything

[crxess]

kayfun - see my Blog to left

Magma - Great flavor dripper if you run single coil 1.0ohm
Dual coil for Cloud maker with decent flavor

Patriot - Dual Coil and will likely get boring - lol

 

[gel drops]

new Cell...did receive your Pm! (K) now I have to figure out how to reply,I'm sure I will be asking quite a few questions.

 

[ian91]

I would go with an Aerotank Mega. Fits nicely on the DNA30. I use a clone of it that I purchased from FT for less than $14. Holds 3.8ml and you can get 1.5ohm coils. I run it at about 12watts. Works well.

 

[gel drops]

I have the mega also still in the box,im using the aspire nautilus at the moment so at least I do have a few things I can put on the mod until I learn more about the other rebuildable types.

 

[gel drops]

I watched A video last night about making a build it looked like he had a small piece of wood with a nail are something to make his coils with? do they sell something like that because he made it look easy!

 

[Keeferes]

They do sell coil jigs. Dark zero comes to mind. There is also a coil winding gizmo on Amazon. I personally just use drill bits.

 

[gel drops]

so far I can tell that people build differently,I'm sure you guys know if some of the materials come with the atomizers that I ordered if not looks like I'm going to be purchasing a toolbox!

 

[Keeferes]

There are a few things you'll want to get. A precision set of scree drivers, a dedicated ohm checker, different gauges of wire, pointy tip ceramic tweezers, nail Clippers, just off the top of my head.

 

[Flt Simulation]

I would go with an Aerotank Mega. Fits nicely on the DNA30. I use a clone of it that I purchased from FT for less than $14. Holds 3.8ml and you can get 1.5ohm coils. I run it at about 12watts. Works well.

Ditto what 'ian91' said !

I normally use an authentic Kayfun Lite Plus, but the Aerotank Mega is really a nice alternative too, especially if you don't like (or have the time) to fiddle around making your own coils and wicks.

I normally use an iTaste MVP 2.0 box mod to power my Mega, but any 22mm diameter mechanical tube mod works well too.


Here is a 22mm HCigar 'Caravela' clone mod (with an adjustable voltage Kick module installed in it) and the Mega setting on top ..... good vape

The Mega comes with a 2.0 ohm coil pack ... For me, I have found that 9.5 watts (4.4v) makes for a nice vape with this coil.

 

[gel drops]

I read people saying this is a 1.5ohm build probably a stupid question but how do you determine what the resistance is going to be before you ever build the atomizer is it determined by the amount of coil wraps? I have a Kayfun lite plus v2 dual air flow,magma and a patriot that should be here by Tuesday I have everything I need 2 make a build this will be my first time trying! Cana by cloupor is what I will be working with however I do have 4 or 5 mechanical mods that I can use as well.

 

[Maurice Pudlo]

Coil wrapping | Steam Engine | free vaping calculators

The steam engine calculator will help you figure out the coil ohm prior to building. Want a 1.0 ohm coil, steam engine can help you get just that.

Maurice

 

[Budkiss]

WOW gel drops... what an amazing photo... those eyes are enough to make me want to GIVE you a kanger tank.
(a compliment, not a come on)

I started with a Vamo v5 and an aetotank w 2.5 dual coils. Was satisfied until i discovered 1.5 coils (which was a major improvement) and then tried a mod that could push past my 15 w (and 1.2 ohm) limits. That was the worst/best thing that could have happened to me. I quickly snatched up an IPV2 and began building coils (which turns out isn't rocket science). I now build various single, dual. sub ohm, twisted kanthal coils (depending on my mood).

There are B&M stores here that would gladly build a coil or two for me if I asked.
Bat those gorgeous eyes and say, "pretty please" and they will be sure to help you out.

 

[Flt Simulation]

The resistance (ohms) of a coil is based on the thickness of the wire your using, how many total wraps of your coil and the inside diameter of the coil your making.

Here is a great little calculator you can use to help you 'design' your own coil:

Coil wrapping | Steam Engine | free vaping calculators

 

[gel drops]

I got 26 wire if that makes any sense Kanthal wire.

 

[Flt Simulation]

What kind of battery are you using?

 

[gel drops]

Sony vtc5 18650 30a 2600mah flat top.

 

[shorty70]

Should be good to go...try 6 wraps and go from there, check it first.

 

[Keeferes]

I read people saying this is a 1.5ohm build probably a stupid question but how do you determine what the resistance is going to be before you ever build the atomizer is it determined by the amount of coil wraps? I have a Kayfun lite plus v2 dual air flow,magma and a patriot that should be here by Tuesday I have everything I need 2 make a build this will be my first time trying! Cana by cloupor is what I will be working with however I do have 4 or 5 mechanical mods that I can use as well.

The amount of coil wraps, the gauge of wire, and the diameter of the coil all contribute to what the target resistance will be.

This link (Steam Engine | free vaping calculators) will help you to figure it out.

Never fire a coil on a mech until you know it's resistance and know it's safe for your batteries. An ohm checker is ideal, but your cloupor will tell you fairly accurately.

 

[graybeard]

Awesome. Kanger Protank 2 with an aerobase. Being in Greenville check out E-Cloud Vapes on 4601-d Whitehorse Rd. Those guys are awesome!

Too cool! I'm in Gaffney and was looking for a decent B&M somewhere close. Upstate vapers rock!

 

[gel drops]

just a few little things I have as you can see all of this stuff is ready out of the box I think it will be cheaper building my own!