If I get an IPV2 50 W, why would I need to get a Mech Mod?

Status
Not open for further replies.

The Cloud Minder

Ultra Member
ECF Veteran
Jul 28, 2014
1,061
1,301
Pittsburgh, PA, USA
I had originally been planning on getting a couple more mods and tanks* before I moved into dripping, but recently I've been reading about the IPV2 50W and it can handle coils down to 0.2 ohms.

So why would I ever need a Mech Mod, even if I wanted to get into rebuildable drippers?


___________________________________________________________________________________________________

*- On the To Be Acquired List : Itaste 134 / Provari 2.5 / LP REOGrand / Aspire Nautilus tank / Itaste VTR / E-LVT /
 

ENAUD

Resting In Peace
ECF Veteran
Verified Member
Jul 23, 2013
9,810
64,089
Bordertown of ProVariland and REOville
I personally don't think it is necessary to use a mech and still enjoy RDA's. I primarily drip when at home, and do so quite enjoyably, on my regulated mods. It's about learning to build efficiently for each particular atomizer, and for your particular likes, such as heat, density of vapor, throat hit, etc. by controlling wicking, airflow, coil size and wire diameter, you can really make some pretty simple atomizers perform very well.

P.S. I learned to drip with a Lavatube with an IGO-L on top :)
 
Last edited:

rusirius

Super Member
ECF Veteran
Verified Member
Aug 8, 2014
615
1,183
DE
I don't think anyone "needs" to get anything... LOL... Why might someone want a mech mod? A good mod will have extremely low voltage drop... They are typically much smaller than a VV/VW mod, especially one that can do high wattage... They can also be quite fancy... And with the right battery can power coils well below .1 ohm...

Now does any of that mean you "need" it? Nope... But if those things are important to you, then you just might want it...

On the other hand, if those things aren't important... Then no, you certainly don't... Powering a coil at 30 watts is going to be the same rather it's a mech or regulated mod doing the driving.. In fact, the honest truth is, if you're not worried about Ultra low ohm coils, or the looks, then the regulated mod is a much easier way to go since it can step up or down the voltage to give you a consistent vape across the life of the battery...

And if you want to run a .3 ohm coil in a dripper there is NO reason you can't do so on a regulated mod... :)
 

Marc411

Vaping Master
ECF Veteran
Verified Member
Mar 17, 2014
4,737
10,918
Windy City
I turned a coworking onto vaping and she is already pretty good building R91's after just a couple weeks. I brought my Vanilla and Viking and she really loved the flavor but didn't want the other equipment.

She now has a Patriot on her MVP2 with a 1.4 ohm coil and is a big fan. She swaps out with a tank for the ride home.

You don't need to go mechanical or sub-ohm to enjoy the great flavor of dripping.

I use my IPV with Kangers a 7 watts to my drippers at 30 W. I like mine, it was a good purchase for the price.
 
Last edited:

Ryedan

ECF Guru
ECF Veteran
Verified Member
Mar 31, 2012
12,869
19,652
Ontario, Canada
The only thing you can do with a mechanical mod you can't do with a 50 watt mod is go over 50 watts. With a 30A battery at 0.14 ohms using all the 30A of the battery, you'll be vaping at around 90 watts with a fully charged battery. At 0.2 ohms you'll be at 21A and around 65 watts.

The mechanical mod will also likely be a lot tougher than the IPV2. So if that's important to you, it is another difference.
 
Last edited:

p7willm

Super Member
ECF Veteran
Verified Member
Apr 11, 2014
936
458
Lansdale, PA, USA
It is not a safe idea, it draws over 42 amps, but a mechanical with a fresh battery and a .1 ohm, again NOT recommended,, will run 176.4 watts. Even a little safer 25 amp draw will produce 105 watts. So, if you throw caution to the wind you can go with a much higher wattage than your 50.

I have also seen a mechanical with 2 batteries in parallel so it should, with the correct batteries, be theoretically capable of 60 amps, and theoretically 252 watts, and weld the button when you press it.
 

The Cloud Minder

Ultra Member
ECF Veteran
Jul 28, 2014
1,061
1,301
Pittsburgh, PA, USA
It is not a safe idea, it draws over 42 amps, but a mechanical with a fresh battery and a .1 ohm, again NOT recommended,, will run 176.4 watts. Even a little safer 25 amp draw will produce 105 watts. So, if you throw caution to the wind you can go with a much higher wattage than your 50.

I have also seen a mechanical with 2 batteries in parallel so it should, with the correct batteries, be theoretically capable of 60 amps, and theoretically 252 watts, and weld the button when you press it.

OK yes, but what does that accomplish? a 15% bigger cloud?, denser? More flavorful? Because you can?
 

Ryedan

ECF Guru
ECF Veteran
Verified Member
Mar 31, 2012
12,869
19,652
Ontario, Canada
OK yes, but what does that accomplish? a 15% bigger cloud?, denser? More flavorful? Because you can?

I've never gone that high, but from what I do know I can say with reasonable certainty that it accomplishes nothing if you don't use the extra power correctly for what you want to achieve.

More flavorful, yes, but that can also be achieved by changing the recipe of your juice and/or the design of your atty. And if you do it wrong you'll get less flavor.

Bigger, denser cloud, yes. More power is not the only way to achieve this, but once you've exhausted the other options this is all that's left that can help you.

Because you can? Well, yes ;)
 
Status
Not open for further replies.

Users who are viewing this thread