I think all the people who have had issues are using the stock coil.
Last edited:
Innokin Axiom
- Thread starter Vinnybagodoughnuts
- Start date
- th_trl_thread_readers 0
- Status
After looking at mine again all the ring does is control the amount of airflow it doesn't stop juice from escaping the tank.I do think that is why it leaked...................I think there is still some juice on the ring...If I get a chance to mess with it today I will try again............
Last edited:
Lemme try again. I received my Axiom yesterday. Great tank though I too had a little seepage from the AFC holes, but only once. Today I built a single coil at .5 ohms and it vapes great and no leaks. I did notice when I took the pre-built coil out that there was a spot where the rubber or whatever it is under the coil housing had come separated from it where it covers two wires. Don't know if that was the cause of my leak but there was a bit of liquid inside the base. Anyway, I'm pretty happy with it. Thanks Innokin!
I tried it again last night an it is leaking where this ring meets the rest of the base.....each time I ran my finger around the place where is meets it had juice on it. I emptied it and dried it all and filled with just a small amount.........and still it's leaking....
Found a decent vape shop here in Temple TX, Wall to wall vapes, decent folks, stop by if you are in the area!
Picked up a spool of 26ga Ti, they didn't have any SS, but I've been itching to try this sucker out in TC so I did a 6 wrap over a 2.5mm mandrel, came out right at .25 ohms. Running it on an SXK Mini Zero at my normal 30w 400deg and it's just downright nice!
I stuck a hunk of wire clean through one of my toes, don't do that, and flooded it when I filled it. Just came in out of the heat, washed it out and probably squeezed the juice in a bit hard is all I can figure as its trucking along fine now?
I'm trying to push this thing to test it, but so far it's turning into one of my favorite tanks.
Picked up a spool of 26ga Ti, they didn't have any SS, but I've been itching to try this sucker out in TC so I did a 6 wrap over a 2.5mm mandrel, came out right at .25 ohms. Running it on an SXK Mini Zero at my normal 30w 400deg and it's just downright nice!
I stuck a hunk of wire clean through one of my toes, don't do that, and flooded it when I filled it. Just came in out of the heat, washed it out and probably squeezed the juice in a bit hard is all I can figure as its trucking along fine now?
I'm trying to push this thing to test it, but so far it's turning into one of my favorite tanks.
I love the factory coils, but I find that on the RBA section the "juice holes" could be larger. Opposite of the RBA for the Isub series. The RBA on the Isub have nice large "wicking holes" that allow for ease of wicking and seem even airier than the factory coils. Whereas the Axiom factory coils the "juice ports" are larger than the RBA.
Overall, I love this tank, gonna order some coils this afternoon.
Overall, I love this tank, gonna order some coils this afternoon.
Just built a dual coil at .43 (was going for .50) but close enough.
I figured out hot to do it pretty easily.
Now I'm gonna try to "rewick" the factory coil.
Fingers crossed.
I figured out hot to do it pretty easily.
Now I'm gonna try to "rewick" the factory coil.
Fingers crossed.
Don't know if its gonna work, but I rebuilt it, new coil and wick.
Also I ordered a silver Axiom and two - 5 packs of coils
Also I ordered a silver Axiom and two - 5 packs of coils
Well mine hasn't leaked anymore and I have put at least 30mls through the original stock coil.I will build the rba when the juice runs out this time. While the flavor isn't as good as my Merlin or Kayfun mini it is decent.
I am sorry to hear you are having problems. I took my afc control ring off and vaped 2 tankfulls to see if that could possibly be the problem but as I suspected not a drop leaked.It has to be the coil or a bad oring.Are you using the stock one?
It would be nice to see someone from Innokin jump in here about the afc ring and whether its supposed to come off but I won't hold my breath.
Last edited:
I was hoping to get some assistance............but for now I have put it away.........after 3 tries...........I am sorry to hear you are having problems. I took my afc control ring off and vaped 2 tankfulls to see if that could possibly be the problem but as I suspected not a drop leaked.It has to be the coil or a bad oring.Are you using the stock one?
It would be nice to see someone from Innokin jump in here about the afc ring and whether its supposed to come off but I won't hold my breath.
I'm sorry, have you tried the rba deck and had problems with it as well?I was hoping to get some assistance............but for now I have put it away.........after 3 tries...........
I was planning on it.....as soon as it cools off some.......it's hard for me to work in the heat...........
Fair enough, I still haven't tried their coil yet but I've had great luck with the rba deck.
I like this tank so much that i ordered another one, besides the one that I won.
Gonna order another when finances allow. (unexpected A/C replacement is holding me back at this point)
Gonna order another when finances allow. (unexpected A/C replacement is holding me back at this point)
How did you Renwick the stock 0.5 ohm coil. Would be great if you could give us an idea on how to open it up.
Opening it is easy........rewicking, not so much.
Remove the little metal "bar" by pulling it straight out. Then remove white rubber grommet the same way.
My re wicked coil did not work.
A friend of mine at work who vapes came by me yesterday and showed me the new setup that he bought. The Disruptor TC and an Axiom tank.
I asked him how he liked the Axiom, and his reply was "dude, the flavor is outstanding"
I agree.
I asked him how he liked the Axiom, and his reply was "dude, the flavor is outstanding"
I agree.
Last edited:
- Status
Similar threads
