Introducing the Griffin Rebuildable Atomizer Tank
- Thread starter gormly
- Start date
- th_trl_thread_readers 0
-
- Tags
- ecigexpress provari vamo vapor pro
- Status
I like it the way it is.
My buddy is a machinist, and if it can't be done without mucking it up, I'll leave it the way it is.
I say if they are set up right with a proper coil & wick the are going to preform the same, flavor throat hit & vapor wise. But I do prefer the Tiamat in appearance it just looks so cool on my Provari and also for the clear tank I have the metal tank on my Griffin ( DiD ) and its nice to see the juice level. But if one is to big or to heavy or one is to small or you want a certain look pick the one that most appeals to you in the end they all work the same and you cant go wrong with any of the three. Hope this helps.
Hey I see the clear tanks are back in stock. 147-4 left.
Last go round I ordered some of the shorty DT's with the intention of plugging them and using them to make leak proof caps. Never happened. I like the way they look, feel, and taste on the Griffin's so much they are all I use now.
Last go round I ordered some of the shorty DT's with the intention of plugging them and using them to make leak proof caps. Never happened. I like the way they look, feel, and taste on the Griffin's so much they are all I use now.
So my clear tank Griffin leaks right out of the box.... and the clear tank replacement for my metal tank Griffin is too tight and shredded my o-ring trying to put it on.. Pretty bummed. Any suggestions?
Get an Ideal 12mm syringe. You can get 3 out of 1 syringe and they fit tight enough to use without o-rings. I have these on all 3 of mine and they work out well.
Thanks, I'll give it a try. Do you have a link? I'm not finding 12mm. I'm also lazy
You can always get 'em from Tractor Supply.
Thanks, I'll give it a try. Do you have a link? I'm not finding 12mm. I'm also lazy
What measurements does the mesh cut need to be for this Griffin? I can't be wasting any, I only have a little.
Also, does anyone know what grade mesh came with it?
Thanks
Also, does anyone know what grade mesh came with it?
Thanks
Im using 3.5cm by 7cm, ut im rolling it pretty tight and its slightly loose in the wick hole to allow air to escape.
Thank you.
Also, I took it apart to clean it, and can't seem to remember which way these screwed back on.
There's a slight difference, depending on which way I face it before screwing it back on... Does it matter?
Also, I took it apart to clean it, and can't seem to remember which way these screwed back on.
There's a slight difference, depending on which way I face it before screwing it back on... Does it matter?
Either it doesn't matter, or the right way is with the tapered part down. At least that is how I set mine up and they all work fine. Be sure to tighten the first nut just till snug. Over tightening can ruin the insulators, or at a minimum make the positive post not make contact with the PV.
to those having leaking issues if you are using the clear tank you need the clear tank orings, according o the manufacturer. the metal ones are not going to fit properly.
I went to my local Hobby Lobby and got some screws that are the right size and thread count. That was after I went to Radio Shack and picked up some 2-56 but were course instead of fine cut. It's always nice to have extra ones around as I've lost a couple on the floor because they are so dang small.
What kind of wire and ss mesh come with this Griffin? The bag is not labeled, several of my bags are not labeled, so now I've mixed them up and don't know which is which.
I tried to edit post but it created a new one? Oh well, it won't let me delete the other one. Sorry.
I tried to edit post but it created a new one? Oh well, it won't let me delete the other one. Sorry.
Last edited:
I think it's 325 mesh & nichrome (don't know the gauge). It's been the same in all 5 I've purchased.
HTH!
HTH!
- Status
Similar threads
- Locked
