Is nhaler juice harder on atomizers

[kcomfort001]

ok I placed an order, quick shipping etc..etc.. but all my atty's are burning extremely hot with the nhaler juices

I only purchased one high voltage juice, is there something I'm missing ?

Had 3 attys getting extremely hot

 

[AshHole]

I think nhalers juices are better for attys! I vaped ecopure for he longest time and saved all my dying attys (hard draw, hot, low vapor).

When I got my nhaler juices, I tried these old attys and they somehow came back to life...

 

[RIMP]

My attys run cooler with the hv Do you prime them with 1-2 drops of juice and keep your cart wet?
RIMP

 

[jennlsnoopy]

I've had no problem with there juice on my atty. Don't know what to tell you.

 

[beckah54]

HV juice doesn't seem to harm my attys. It's mostly all I vape.

 

[hittman]

I use a little HV liquid but mostly the 24mg from nhaler. I had only lost one atty in four months until I started using the xhaler at 5 and 6v. I have lost two 901 attys but I believe that one was my fault and the other was just faulty and I got it replaced under warranty. kcomfort, what device are you using? 510's seem to me to get hot no matter what liquid I use whether it's nhaler or not. To me even the 24mg is thicker than some of the dekang liquids I have used. When using a 510, I top of the cart and put two drops right on the atty.

 

[kcomfort001]

no its not hv juice, i'm just having carts slightly melt now and everything, could just be 3 bad atomizers and I use a 510, how is the xhaler btw? worth it?

 

[Bigbuyer]

I love that Xhaler. It is worth it. Not using it in public though...

 

[hittman]

It has had a few quirks like any newly released mod but I think it was worth the money. It came with 510,901,and 801 fittings, attys for each, two 3v batteries for 5 or 6v with a charger, two 3.6v batteries and a charger all for $145. Somewhere on this forum is a picture of how to align your cart. Have you tried that. I have only melted a cart before on 5/6v. I would have a hard time believing that you had three bad attys. Are they hard to draw through? Does it seem like you are getting good airflow and how long are you holding the button down. Are you using standard 510 batteries?

 

[kcomfort001]

It has had a few quirks like any newly released mod but I think it was worth the money. It came with 510,901,and 801 fittings, attys for each, two 3v batteries for 5 or 6v with a charger, two 3.6v batteries and a charger all for $145. Somewhere on this forum is a picture of how to align your cart. Have you tried that. I have only melted a cart before on 5/6v. I would have a hard time believing that you had three bad attys. Are they hard to draw through? Does it seem like you are getting good airflow and how long are you holding the button down. Are you using standard 510 batteries?

yeah standard 510 batteries, heard lots of gurgling the heat from the atomizer seemed almost as if it sucks every bit of liquid into the wick I can get lots of vapor if I hit it directly from the atomizer vs. a cart but carts will slightly melt at the top

 

[m00nshake]

I was having troubles similar to yours when I first received my HV liquid from Nhaler. I thought that something was wrong with the liquid because I wasn't getting the massive amount of vapour that a HV should produce and it was taking a long time to get a decent hit.

Turns out it was the atty I was using, which was about two-weeks old when I got the Nhaler liquid. I switched to a new atty and now Grape Ape HV is vaping perfectly. By the way, I am vaping with a Silver Bullet PV with 510 atty and Lipton tea bag mod.

 

[JustJulie]

Your problem with a melting cart may be as simple as cartridge alignment. The second post in the following thread has a picture showing you how your cartridge should be aligned in a 510 atomizer: http://www.e-cigarette-forum.com/fo...updated-v2-0-slug-search-over.html#post695024

 

[kcomfort001]

Your problem with a melting cart may be as simple as cartridge alignment. The second post in the following thread has a picture showing you how your cartridge should be aligned in a 510 atomizer: http://www.e-cigarette-forum.com/fo...updated-v2-0-slug-search-over.html#post695024

its aligned properly it didn't melt alot just slightly at the top.

 

[crashtestjeep]

It COULD be how hard/long ur hitting it. Haler liquids tend to be VERY tasty and make people want to double/triple hit, lol. I have never melted a cart, even at HV, but my roommate has simply because he draws super hard/long......

 

[kcomfort001]

It COULD be how hard/long ur hitting it. Haler liquids tend to be VERY tasty and make people want to double/triple hit, lol. I have never melted a cart, even at HV, but my roommate has simply because he draws super hard/long......

hmmm that could be it, I was wondering what that plastic taste was, I don't think I'll be satisfied until I have plastic melted to my lips


No really though got some new atomizers tons of smoke or smoke like stuff eh, heheh lol no idea whats so funny it just is.

 

[Promise]

I actually have a few cart that have melted edges but I know that is me, cause I do take very long draws.