kanger protank 1

[nextminttwist]

any user of protank 1 ? seem like many complain of leaking , does all of them come with leaking problem ?

 

[zosman]

Protank 1 a lot of complain cos some base does not have the silicon...i think due to mass production they might have forgot to slot in and also the base thread always slant

Sent from my GT-I9152 using Tapatalk now Free

 

[earlgrey]

Protank 2 have the same leaking issue as well anyway..

 

[zosman]

Lucky for me...my protank 2 never fail on me...no leaking from day 1.....

Sent from my GT-I9152 using Tapatalk now Free

 

[nextminttwist]

Protank 1 a lot of complain cos some base does not have the silicon...i think due to mass production they might have forgot to slot in and also the base thread always slant

Sent from my GT-I9152 using Tapatalk now Free

silicon as in gasket ? base thread slant , that sounds bad

 

[zosman]

What to do china come mah...

Sent from my GT-I9152 using Tapatalk now Free

 

[zosman]

Or....altenatively u can try puritank

Sent from my GT-I9152 using Tapatalk now Free

 

[dragonl]

silicon as in gasket ? base thread slant , that sounds bad

Might be a clone. Protank has several clone.

 

[nextminttwist]

Might be a clone. Protank has several clone.

wow , knock off ?

 

[errolng]

i do get leaking on the pt2 when juice is low

 

[dragonl]

i do get leaking on the pt2 when juice is low

PT2 lost it vacuum when juice is low, thus it will leaks. U have to maintain 1/3 full to prevent leaking.

 

[desmondsg]

Frustrated with my iclear30. Heard many good things about Protank2.

 

[dragonl]

Frustrated with my iclear30. Heard many good things about Protank2.

A better improvement but will leaks if u empty it fully. Bro, do u need to buy that many protank2?? All u need is the coil head replacement or u can rebuild it wil SS mesh and micro coil.

 

[desmondsg]

A better improvement but will leaks if u empty it fully. Bro, do u need to buy that many protank2?? All u need is the coil head replacement or u can rebuild it wil SS mesh and micro coil.

Don't need, just buy and keep LOL.

 

[mightymen]

Inexpensive bottom feeder tank. That I can make DIY coil/wicks for less than few cents. I don't get leaks. I never hold the glass part when unscrewing or screwing back on and never over tighten it snug is OK.

 

[vlad4848]

I have been using protank 1 for almost 4 months now with zero leaking. I still have my new protank 2 unused.
I have not altered the wicks stock set up

 

[Kryxwee]

Wow, nice picture.

 

[SonHouse]

I have a number of ProTanks I have been using for about 6 months. I've never seen leaking though the top of my battery will get wet from condensation and juice flooding. Not a big deal, I carry QTips and clean it out if vapor production starts dropping.

 

[Stingbk]

I got talked into a pt clone at my brick and mortar shop and I love it. It's the anyvape davide, pyrex tube, changeable drip tip and it came with and ego Beaty ring skirt. With the skirt on my ego twist it looks good and performs great. It may gets bubbly around 1/3 of a tank but I usually take it off and blow it out into a tissue holding the tank upside down and screw it back on and finish the tank up. Love it.

 

[errolng]

yep this always happens when the jucie is low.
hate it when it starts gurgling.

I have a number of ProTanks I have been using for about 6 months. I've never seen leaking though the top of my battery will get wet from condensation and juice flooding. Not a big deal, I carry QTips and clean it out if vapor production starts dropping.