Hey everyone I just received a couple kanger products in the mail. First off is the protank which in the first 3 hours has been absolutely perfect. The other product was the kanger evod, and seeing how I'm somewhat new to vaping, my problem is that my liquid is leaking through the clearomiser to the top of my battery. Is this a normal occurrence or am I dealing with something that is natural. My setup is a joyetech ego-c with the upgraded battery. These are the first clearomisers I have purchased, I was previously using the ego-c tanks that came standard with my kit. Any and all input would be great.
Leakage?
- Thread starter MJGraveline
- Start date
- th_trl_thread_readers 0
- Status
Some folks are reporting that the protank might leak/gurgle if its juice
level gets below 1/3. Mine hasn't so far though.
level gets below 1/3. Mine hasn't so far though.
I think the evods are like the t3's (someone correct me if wrong).
If it is gurgling that might result in that leakage you are mentioning. I fixed a gurgling T3 with a small slice of a cotton facial pad. I pulled the post above the coil and gently inserted my new flavor wick just above the coil and reassembled. (this is real easy)
remove your head
gently blow the shaft out to get any extra juice out.
gently wiggle the top shaft from the coil section to remove it.
place your 'flavor wick' on top (it doesn't need to be very big)
re-seat the top shaft. (may need a little force)
fill your clearomizer and put the head back on and test.
Still gurgley? add more wick.
To hard to draw? Too much wick.
HTH.
The ProTank is slightly different in the way it is assembled but the same process works as well.
If it is gurgling that might result in that leakage you are mentioning. I fixed a gurgling T3 with a small slice of a cotton facial pad. I pulled the post above the coil and gently inserted my new flavor wick just above the coil and reassembled. (this is real easy)
remove your head
gently blow the shaft out to get any extra juice out.
gently wiggle the top shaft from the coil section to remove it.
place your 'flavor wick' on top (it doesn't need to be very big)
re-seat the top shaft. (may need a little force)
fill your clearomizer and put the head back on and test.
Still gurgley? add more wick.
To hard to draw? Too much wick.
HTH.
The ProTank is slightly different in the way it is assembled but the same process works as well.
Last edited:
Im pretty new as well I just upgraded from a 510 to a ego-c 1000 mah batt friday. I got a mt3 clearo for it. It works fantastic but I also had some leakage and gurgling the first day. What seemed to be the problem for me is that I was hitting it too hard and or not enough time between drags. I found that if I hit it slightly lighter (still getting plenty of vapor) and give it some time between hits it is working fantastic with plenty of vapor and TH. Good Luck!!
All good tips.
Might also make sure the head / coil assembly is tight.
I usually clean all my new devices before use, just to get the manufacturing gunk out, and have come across a couple who's coils were loose from the factory.
Might also make sure the head / coil assembly is tight.
I usually clean all my new devices before use, just to get the manufacturing gunk out, and have come across a couple who's coils were loose from the factory.
I have the exact same question, if juice dripping onto the battery is normal. My newish tanks, a CE4 and a T3 have both done this. Didn't know if I was not sucking out all the vapor and it was condensing back down the center tube or what. No real other leaks beside this.
I haven't had any issue with my pro tanks. I can confirm that my eVODs leak when I'm down to about 1/3 of a tank. It's not a huge deal. I usually just fill the tank back up before it gets too low now that I know the cause. I might try the wick upgrade at some point to see if that helps though.
- Status
Similar threads
