Looking for comparable tanks

[keha]

Looking for a kayfun/lemo1(not 2 or 3) type tank that has a flip top like newer sense tanks or a fill top like tfv8.

Basically I want to vape around 20-35watts, single coil, with low or no noise like you get from a kayfun/lemo. But with a flip top fill like sense blazer or a top fill like tfv8. 4+ ml capacity, with a rebuild-able deck. Don't want a twist off one like kayfun-prime offers.

I bought a tfv8, hate the loud noise. Hate that even if I use same coil I build for kayfuns/lemo all the sudden requires 50+Watts just to barely work. Then the tfv8 constantly gags me, unless I build a dual coil setup and vape over 80watts. I don't understand that, on why it doesnt work the same if I built same coil as my kayfun/lemos.

I also get more vapor production out of my kayfun/lemos and butter smooth vape 99% the time. Than I do out of my tfv8. I mouth to lung, no straight inhale.

So if any of you have a recommendation to check out, I thank you. Much appreciated.

Been looking at a "Sense V-jet tank" the one that comes with the mod in a kit. Since it seems the rebuild-able decks for atlantis will fit. I already own this tank, but not the rebuild atlantis part. Anybody able to confirm if the "Vjet Tank" or "Blazer mini" will accept atlantis coils?

Thank you all for reading and thank you in advance for any recommendations or info.

 

[ScottP]

Maybe look at the Innokin Ares tank.

 

[Coastal Cowboy]

Serpent Mini is 22mm, single coil and top fill. Capacity is only about 2.5ml (slap full). But its limited airflow makes it ideal for 25-35 Watts.

OBS Engine Nano is well regarded and alleged to be leakproof. I don't own one of those yet.

I do own a Serpent Mini and use one regularly but with temp control. It settles in for me at about 38 Watts.

 

[ScottP]

Serpent Mini is 22mm, single coil and top fill. Capacity is only about 2.5ml (slap full). But its limited airflow makes it ideal for 25-35 Watts.

OBS Engine Nano is well regarded and alleged to be leakproof. I don't own one of those yet.

I do own a Serpent Mini and use one regularly but with temp control. It settles in for me at about 38 Watts.

I haven't used the mini, but I use the Serpent SMM daily. It too is a top fill (removable top), single coil, and airflow can be limited (may need separate drip tip). I use it in TC at < 30 watts and 435F.

 

[stols001]

The ares might be a good choice if you want something a bit less restricted, but not supremely sub0hm, it's designed as a MTL tank but it does have enough airflow wide open that you could probably put a lower resistance coil in there and vape it fairly happily , while not getting "choked" by vapor, and it gets good flavor. The Siren V2 is nice as well, although some folks find the flavor a bit more inconsistent, it's also an "airier" MTL vape that could probably handle a lower resistance coil and still give you more vapor.

If you want a drop in tank, maybe something like t he Crown Uwell 3 would work, it's kind of a crossover tank although in my opinion really designed more for sub9hm vaping but there are tons of coil options at various resistances and it's a pretty flexible tank. You can definitely sub0hm with it, but it does have coils up to a 1.2 coil, I belive. I don't own one but I have considered it as people seem to be pretty consistently happy with them, especailly in regards to flavor.

Best of luck,

Anna

 

[Fidola13]

Looking for a kayfun/lemo1(not 2 or 3) type tank that has a flip top like newer sense tanks or a fill top like tfv8.

Basically I want to vape around 20-35watts, single coil, with low or no noise like you get from a kayfun/lemo. But with a flip top fill like sense blazer or a top fill like tfv8. 4+ ml capacity, with a rebuild-able deck. Don't want a twist off one like kayfun-prime offers.

I bought a tfv8, hate the loud noise. Hate that even if I use same coil I build for kayfuns/lemo all the sudden requires 50+Watts just to barely work. Then the tfv8 constantly gags me, unless I build a dual coil setup and vape over 80watts. I don't understand that, on why it doesnt work the same if I built same coil as my kayfun/lemos.

I also get more vapor production out of my kayfun/lemos and butter smooth vape 99% the time. Than I do out of my tfv8. I mouth to lung, no straight inhale.

So if any of you have a recommendation to check out, I thank you. Much appreciated.

Been looking at a "Sense V-jet Tank" the one that comes with the mod in a kit. Since it seems the rebuild-able decks for atlantis will fit. I already own this tank, but not the rebuild atlantis part. Anybody able to confirm if the "Vjet Tank" or "Blazer mini" will accept atlantis coils?

Thank you all for reading and thank you in advance for any recommendations or info.

I have the Sense V Jet if you don’t like noisy tanks don’t buy it! It was my 1st thought on my 1st inhale - wow it’s loud!

 

[keha]

I have the Sense V Jet if you don’t like noisy tanks don’t buy it! It was my 1st thought on my 1st inhale - wow it’s loud!

Yea the coils it comes with are loud. I tried to see of an "atlantis rebuild-able deck" would fit in the Vjet tank, almost does but doesn't fit. You could build a coil on the vjet, but its a big hassle.... Would have to vertical coil it and fully wrap it. Anytime you get an enclosure like this, you can't really get out the hot spots. Plenty of hot spots on majority of pre-made attys. It adds alot more noise to vaping.

These the times I wish I had a CNC machine : /. Feel this part of the market isn't being properly addressed at the moment.

I really love the fill method on that tank, vjet sense.

Doesn't seem anything out to fit what I want out of a tank. Going to rethread my lemo chimney to fit the vjet top. File down inner circle on vjet tank to fit lemo glass, then see if it works out. If it doesn't, guess I'll just wait till someone else makes something close. Probably use the kayfun prime till then, which is in the mail.

Thank you all for information, anymore suggestions would be great.

 

[ScottP]

Yea the coils it comes with are loud. I tried to see of an "atlantis rebuild-able deck" would fit in the Vjet tank, almost does but doesn't fit. You could build a coil on the vjet, but its a big hassle.... Would have to vertical coil it and fully wrap it. Anytime you get an enclosure like this, you can't really get out the hot spots. Plenty of hot spots on majority of pre-made attys. It adds alot more noise to vaping.

These the times I wish I had a CNC machine : /. Feel this part of the market isn't being properly addressed at the moment.

I really love the fill method on that tank, vjet sense.

Doesn't seem anything out to fit what I want out of a tank. Going to rethread my lemo chimney to fit the vjet top. File down inner circle on vjet tank to fit lemo glass, then see if it works out. If it doesn't, guess I'll just wait till someone else makes something close. Probably use the kayfun prime till then, which is in the mail.

Thank you all for information, anymore suggestions would be great.

Have you seen the Dominator tank? It has the kind of fill port you want, has both pre-built coil heads and a single coil RBA deck included. This or the previously mentioned Innokin Ares tanks seem to be the closest to what you are asking for.

 

[Letitia]

Engine Nano is versatile. I primarily use a ss tri core fc in mine with af set to flavor. Close af by 75% and you can get a nice restricted draw. Mine are usually at 23-24w.