Looking for my first high end Mechanical! What offers the features i want? That is under 260 and is well worth it?

[maf2k8]

I am looking to add 1 LAST and FINAL Mechanical mod to my collection and i could sure use the advice of others out there.

I have experimented and owned a few lower end mechs ( clones ) that were pretty awesome ( and some were complete junk ) and now that i have more experience, I would like something better.

I currently own a N-Zonic v3 which i love but i am wanted another one.

I know that there are a few low cost, great quality, perfect working clones out there but i am not much a fan of the clones ( since i already have owned my share of them )

I will list the features that i am interested in and maybe someone out there who has more experience with them or Someone who owns a endless number of top shelf mechs, Can maybe point me in the right direction?

My budget us 260.00 or less.

There are just WAYYYYY to many mechs out there these days, I cant even keep up anymore! When i do find a mech i THINK i might like? Its either sold out or impossible to find!

So with that said, If anyone could give me some advice as to which mech might be right for me ALONG with which place i can find one? ( other then the classifieds ) I would be very thankful! I am always uncertain about ordering from retailers in other countries simply because, I dont know how there service is on shipping to the U.S...

What i am looking for..

1) It either has to be a side mount switch ( top or bottom is fine ) or if its a bottom button switch, I prefer it to have a switch design to where you don't need to spin the locking ring in place every time you go to set it down, Something with a recessed button to where you can stand it up firmly since the button is recessed.

2) Must have a FLAT top cap! I am not a fan of top caps with a bevel/curve/rounded top. I like my RBAs/RDAs to match up

3) Must be the common diameter of most Mechs out there ( 21mm-23mm) I like it to match well with my RBAs

4) I would prefer a floating or a adjustable center pin, So i can have most everything sit flush.

5) Must accept nothing smaller then a 18490. I only use 18490/18500/18650 batteries, Not a fan of anything smaller

6) Must not be a Hybrid ( i already have one )

and that should about do it! Those are some pretty usual requirements and there are MANY mechs out there ( plus a ton that i have never heard of i am sure )

So with that said, If anyone can recommend a few ( that can actually be found ) i would be VERY thankful!

If you happen to know a place that carries it, Could you also comment on how there shipping is to the U.S. ( because i know most of the good mechs are not in the U.S )

Thanks!!!

 

[D. Waterhouse]

For a bottom button there is always Super T PrecisePlus or ELA. For a top side button I'm looking at the Atmizoo Roller.

 

[State O' Flux]

Hit this, and scroll down to "mods, Mechanical". The Atmizoo Roller that Mr. Waterhouse is looking at is actually at the very top of the ratings list. Up to the top of the page, Vape Squad has a written review of each mech with a "Top 10" listing from both editors and users.

 

[vaporator2000]

Atmoixani's telescopic 69 is an amazing device that is my daily. You are looking for a button lock, draw regulator, and silver contacts. This one is available for around $190 and each has its own serial number. It is barely bezeled and the button can be switched from top to bottom position. Available at vaperev.com.

 

[Coldpunk]

GP Paps. Best. Switch. Ever.

I picked up a SS 2.5 from Domo for 140. Unbelievable value at that price.

 

[maf2k8]

Its looking like a Poldiac or a GP Paps at the moment.

Any major Cons between the two?

 

[donnah]

Nothing against the poldiac but it's a little too ornate and busy for my taste. they're beautiful though. I'm partical to my Roller.. it has all the attributes you listed

 

[Rule62]

My favorites are my Poldiacs. I have two. Other than that, Roller, Nemesis, GP Paps.

 

[maf2k8]

Is the Roller made of SS? or what material is it made of?

 

[Rule62]

Is the Roller made of SS? or what material is it made of?

Yes, the Roller is 304 SS.

 

[Raynman]

I don't know if you have considered this but check out a Reo Grand. You can get a Reo Grand and a RM2 for it for under $200. American made the Reosmods forum under the vendors area has a wealth of information. Even the owner of the company/maker of the mods is on that forum. You'll have a bottom feeder mod with a 6 ml bottle of juice that feeds the mod with a 18650 battery. If by chance if you don't know about this mod or haven't looked into it stop by that forum and lurk for a couple of days. You'll see how nice and helpful those folks are. Only thing that might be a turn off is that it's a box mod rather than a tube. Just my HTH

 

[evgeny131]

POLDIAC!!!!!

you will never regret owning one....its an INCREDIBLE device!

 

[Bullet1231]

GP paps and never look back