I'm looking at the mad hatter rda right now for my next setup, I noticed it's a lot like the freakshow with the bottom airflow system. Does anyone have a mad hatter and what do you think of it?
RDA Mad Hatter RDA? opinions?
- Thread starter 96_Special
- Start date
- th_trl_thread_readers 0
- Status
Ok... Here we go... I just got the Mad Hatter rda. I looked it up on YouTube and checked out several of the reviews first. This is the link that I found most helpful:
He does point out that there is no flavor transferred from the very heating coil (that does work like a charm), however I got the copper one and there is a little flavor transfer from the copper. I solved this by adding a drip tip. Now, he does mention that a drip tip will not fit and I suppose that is true. My drip tip from my Aspire Atlantis does not fit, however, you can use a drip tip from a KangerTech Sub Nano tank (or something compatible).
It came in a combo set with the Panzer Mechanical Mod by MCV. So far the reviews seem pretty accurate. It is a very nice RDA. It is like the FreakShow in set up. It, however, has a substantially deeper reservoir and of course the flip top. I have been vaping on it for only a couple of hours and apart from the lid not closing completely when you first get it, once it gets moisture added to where the gasket is it closes completely without any issues. One of the other issues that I came into it was, I like Clapton coils. And the usual one I recently got into was the 24/32. With two coils it is near impossible to fit the two ends into the center post (I had to compress the coils down and essentially reform the the end pieces and wrestle with it). I didn't put this into the RDA yet but I measured it out and did a little testing with an RDA that I have that is really close. I am using, at the moment a tiger coil and it is perfect although a little hotter than I am used to. I hope that this helps out.
He does point out that there is no flavor transferred from the very heating coil (that does work like a charm), however I got the copper one and there is a little flavor transfer from the copper. I solved this by adding a drip tip. Now, he does mention that a drip tip will not fit and I suppose that is true. My drip tip from my Aspire Atlantis does not fit, however, you can use a drip tip from a KangerTech Sub Nano tank (or something compatible).
It came in a combo set with the Panzer Mechanical Mod by MCV. So far the reviews seem pretty accurate. It is a very nice RDA. It is like the FreakShow in set up. It, however, has a substantially deeper reservoir and of course the flip top. I have been vaping on it for only a couple of hours and apart from the lid not closing completely when you first get it, once it gets moisture added to where the gasket is it closes completely without any issues. One of the other issues that I came into it was, I like Clapton coils. And the usual one I recently got into was the 24/32. With two coils it is near impossible to fit the two ends into the center post (I had to compress the coils down and essentially reform the the end pieces and wrestle with it). I didn't put this into the RDA yet but I measured it out and did a little testing with an RDA that I have that is really close. I am using, at the moment a tiger coil and it is perfect although a little hotter than I am used to. I hope that this helps out.
I was thinking about getting one of these at the vape shop by my place. Is it decent for on the go?
Huh... guess my experiance was different. I bought the copper one and loved it the first day. Had the normal issue of the cap not closing properly and had a hell of a time Fitting my 24g twists in the post holes. Finally got a decent could setup installed and liked it the next day. I'm sure it'd just me overdripping, but I always get juice dripping out of the airholes. This was my first and only rda with bottom airflow. It now sits on my shelf in the closet. Eventually I am gonna list it in the classies and try to get a few bucks out of it, but when ever I think about doing that I'm not home and can't snap pics of it.
I had the same problem that developed. What it is, is that the one that they initially put on is poorly fitted, Try using the one that comes in the spares packaging. It seems to work better.
- Status
