Meatsneaker box meets lava tube guts.

[bstedh]

Sent from my MB855 using Tapatalk 2

 

[DrMA]

Very nice. What was wrong with the lava tube?

 

[bstedh]

The connector and top cap were toast on the lava tube. So, I ripped out the guts and transplanted them.

Sent from my MB855 using Tapatalk 2

 

[Celcius666]

Were did you put the fire button on the mod?? And how/were dud you solder + and - to the board. .
By the way, its a nice looking mod

 

[BkoJoe]

Very nice, i was thinking about doing this to the V2 Lava tube

 

[bstedh]

Were did you put the fire button on the mod?? And how/were dud you solder + and - to the board. .
By the way, its a nice looking mod

If you look at the first pic the fire button is a long shaft tack button. You can just see the nub of it sticking out from the left side top of the box. I spliced into the leads from the factory button which is remote from the board. Hard to see but it is located just to the left of the Battery +. The leads for the switch are just to the right of the V up button. You can just see the two little solder pads.

Batt + is center bottom of the board.
Batt - is either edge just above the display. You can see mine to the left and just above the display.

Atty +/- re-used factory wires. left of center top of board.

 

[Supasm]

Very nice, i was thinking about doing this to the V2 Lava tube

Stay away from my pink one.

And that turned out bad .....

 

[Supasm]

Uhm I did not mean to write that it turned out bad. I think I've been edited. Let me rephrase... That turned out awesome!

 

[Celcius666]

Thanks a lot m8 i defently want to try it out.
I have a lava laying at my table which i don't use so of course why not make another mod out of it, i have almoste all the other parts for it only thing i need to finde is a box

Can i get you to take some closeups pictures of the board and your solderings, that will make my day so happy

 

[bstedh]

Unfortunately all my soldering is on the back side and the board is hot glued in but once you pull apart your lava tube it will be obvious.

I had to cut mine completely apart with a dremel as everything appeared to be glued together fairly thoroughly.

Sent from my MB855 using Tapatalk 2

 

[Celcius666]

Sorry m8 my mistake, i ment not the back side... just closeups of the board as it is right now, from the front so i can better can se where to put the wires an stuff

 

[Celcius666]

Hi there. .
I made a little drawing, can you please tell me if im right.
Im not so good at this right now but trying to learn, i have made som evercool mods but that's all..

 

[bstedh]

It looks like you have the battery and atty connections mixed up. The atty connection is at the top and the battery is at the bottom and side.

Sent from my MB855 using Tapatalk 2

 

[bstedh]

Sent from my MB855 using Tapatalk 2

 

[Celcius666]

Thank you so much
Now im ready for mod'ing in the morning, damn im looking forward to go ahead with this. . Just have to finde a box somewhere, or just go down to the woodstore an buy some wood for it
Thanks again,:thumbup: for you..

 

[Beeznuts614]

Hi Bstedh,
As you seem more than qualified working on the Lava Tube I have a question maybe you could help out with. I have a first gen. LT (black) that occassionally won't fire. While holding down the fire button the display shows "Lo". Curious if you have seen this error or understand why it occurrs? Any feedback would be great, I've only had the LT for 2 1/2 months. Thanks!

 

[tmassey]

pretty sure that means the battery needs to be changed. with the LT v2 it says Lo V. but you can usually vape it for awhile after it shows up,if i remember right...been awhile since i used my LT v1. if you press the red button 7 times rapidly it shows the batt. voltage, mine would start showing low at like 3.5 volts i believe