- Status
I'm using two of the Wotofo Profile v1.5 on a Pico 2 squeeze & VandyVape Pulse II. Getting a good vape just remember to squonk to keep that mesh wet. Also running a VandyVape Mesh v2 (I think that's what it's called) on a Dovpo TopSide. About the same as the Profile but I would give the edge to the Profile (personal taste). If you really want to stretch out a bit, try the Zeus X Mesh rta and/or the Wotofo Profile RDTA. They aren't bad either for your non squonk devices.
What do you want to know?
Mesh is all I use, Genesis tanks, In'ax mesh drippers & carto.
Last edited:
Do Tempco and similar non-vape companies sell mesh that's usable in a mesh atty or do you have to basically buy your mesh from a vape retailer in a vape branded package?
Non vape companies, generally sell raw unclean or chemically treated varieties of mesh material. Basically buy your SS mesh from a reputable vape dealer.
I get mine from a company called: Mesh by Karlson.
He actually manufacturers his own mesh materials, and varieties of rope type wires, specifically for Genesis tanks and attys, to be used at lower wattage, with maximum output.. The results from his material are remarkable.
@CMD-Ky
When you hear Genesis tanks, or attys, most people think, it's complicated to build, and no vapor....holy hell dry hits! Working with mesh wicks ole school style, is very easy to work with, and wrapping the coil is straight forward.
In'ax dripper with the bottom feed pin is a very good atty for squonking, and easy to build. It's a Genesis Dripper. I use them,.
My other go to is the In"ax Carto. It's basically a Genesis style Cartomizer.
Last edited:
Here's a build I did a couple days ago.
It should look something like this. (under the hood)
It's all about your build, and materials. You wouldn't think that this tiny Genesis would perform this well, but they can if built properly.
Check the vid.
In'ax Carto v1
Mesh by Karlson,
CATenary Rope
2/3 wraps @ .67ohm at only 10.5w
Juice is 60vg.
It should look something like this. (under the hood)
It's all about your build, and materials. You wouldn't think that this tiny Genesis would perform this well, but they can if built properly.
Check the vid.
In'ax Carto v1
Mesh by Karlson,
CATenary Rope
2/3 wraps @ .67ohm at only 10.5w
Juice is 60vg.
Last edited:
@Kn0ttYFive
Thank you, very helpful. You gave everything I need to know to get going. I am going to give one a try.
Thank you, very helpful. You gave everything I need to know to get going. I am going to give one a try.
The last couple of years that I vaped I only used mesh atty's. Have 29 of them, and 23 of them are squonk mesh RDA's. The 10 Wotofo Profile Mesh RDA's, 10 Digiflavor Mesh Pro RDA's and 3 Vandy Vape Mesh RDA's are squonkers, and were favored in that order. I also have 6 Wotofo Unity Mesh RTA's that I ran on mech's and TC's.
I used some non vape SS sheet mesh in the mesh RDA's that was left over from the long ago genesis atty days. That said the mesh from the vape companies is easier. I mostly used OFRF nexMESH and Wotofo mesh in mine (and Firebolt Cotton Wicking) FWIW.
Agree, the Wotofo Profile Mesh RDA's and Wotofo Profile Unity Mesh RTA's are about as easy as it gets in squonk RDA's and RTA's with their spring loaded decks.
My favorite combo is a Profile 1.5 with a Dovpo Carbon Dual, love the YiHI board. The worst is the Dovpo Topside Lite which is really great but let down by a very poor board.
- Status
Similar threads
- Locked
