Mod stand that fits in a cup holder?

[Wayne Wasted]

Does anybody make something that fits in a cup holder that keeps my Vamo secure? Figured it wouldn't hurt to ask.

 

[Tjloa]

If your looking for something for the car check this thread. Good Luck

http://www.e-cigarette-forum.com/forum/e-cigarette-accessories-discussion/375876-looking-pv-holder-car-picked-up-couple-days-ago.html

 

[Snkinep]

Is that a one inch diameter?

 

[BigLebowski]

Here is the link to Waxy's modblok. They have a sizing guide as well.

 

[Bob Chill]

My buddy said he saw someone using a piece of cut pool noodle that fits right into a cup holder and holds a vamo perfectly snug.

I have enough material in the house to make 100 of them. Hmmm...pool noodles cost 2 bucks and make about 10 holders....i could sell each one for $5...hmmm.....

 

[John_]

Could also just be stands if you cut the bottom flat.

My buddy said he saw someone using a piece of cut pool noodle that fits right into a cup holder and holds a vamo perfectly snug.

I have enough material in the house to make 100 of them. Hmmm...pool noodles cost 2 bucks and make about 10 holders....i could sell each one for $5...hmmm.....

 

[BostonJim]

I had an old cup holder ashtray for my truck as the Ford Explorer doesn't have an ashtray at all. ..., no ashtray? where do non-smokers put their change? Whoops, I almost lost it again for a minute there, I'm back. Ok so when I quit smoking I cleaned the ashtray thing, tossed the cig holder part and had just the cup. I found a piece of styrofoam, slammed the open end of the cup on it, trimmed the edges, bored a few holes, Vamo, I have a ego/ Vamo holder in my truck

 

[savagemann]

How about some pipe insulation from the hardware store.
It's cheap and should fit most cup holders.

 

[OBDave]

My buddy said he saw someone using a piece of cut pool noodle that fits right into a cup holder and holds a vamo perfectly snug.

I have enough material in the house to make 100 of them. Hmmm...pool noodles cost 2 bucks and make about 10 holders....i could sell each one for $5...hmmm.....

Ha, I get the same thought considering how many Ego holders I've made for friends and around my house from the single 2x4 and 2x6 scraps I had laying around. Five minutes, a 5/8" drill bit and a Skil saw = new career!

EDIT: For my car, I have this thing called a "door handle" that my e-cigs sit in pretty nicely...check your car and see if it has one too. Very economical!

 

[Vpong23]

Sounds like i need to buy myself a pool noodle

 

[brun019822]

Waxys modblok is awesome I have one for the car and home

 

[vwkitty]

AutoZone and the such sells foam cup holder inserts meant for a cell phone and pen, that might work. I've never had a problem just putting mine anywhere in my car though. Cup holder, passenger seat, cubby in front of shifter.

 

[retired1]

Custom Wood PV.....Ecig Holders - Home Some nice ones there as well.

 

[Bill's Magic Vapor]

VapeCrate has them (Stained $12):



VapeCrate - Home

Wayne Church at Custom Wood PV ecig Holders ($22):



Custom Wood PV     Ecig Holders - Home

And, Waxy's Mod, as mentioned above ($60):



Waxy's Modblok Piston Series Car Caddy Cherry/Zebra Wood #26 - Detailed item view - WAXY'S MODBLOK

I have used both VapeCrate and Custom Wood PV Ecig Holder, and Darrin and Wayne are both excellent to work with, allow customization, take one to two weeks plus shipping, and I'm delighted with their products. Back in the day, I did a lot of wood working myself. But my shop is no longer, and the pricing is very good. Other than the joy that is wood working, you wouldn't save much money, on the cup holders. I got the mod holder units, each a ten mod unit, both custom to match my gear. Highly recommended. Best to you.

 

[Anaideia]

I went to those pottery painting shops, and got a short pencil holder....that way I was able to paint it how I wanted.

I have a friend who uses a beer cozy

 

[Dj_Jedi]

Bout to try a pool noodle or a cup ashtray to a custom mod holder lol

 

[cocacola31173]

I had one of those ashtrays that looked like a cup. I cleaned it out really good and got some soft foam and cut out a hole that would fit my mod...works great.

 

[Dj_Jedi]

I had one of those ashtrays that looked like a cup. I cleaned it out really good and got some soft foam and cut out a hole that would fit my mod...works great.

Awesome I'll try that out. Thanks